R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 2
1
2
Search: Posts Made By: TryHard
Showing results 1 to 25 of 26
Search took 0.00 seconds.
Forum: Radio and Electronics
03-14-2015, 10:38 PM
Replies: 734
Views: 201,937
Posted By TryHard

If you set boost and turbo timing values to Zero...

If you set boost and turbo timing values to Zero in any profile, the esc will be in blinky mode, and the led red will blink in neutral.
What you describe with the blinking green lights is just the...
Forum: Radio and Electronics
01-31-2015, 08:02 PM
Replies: 734
Views: 201,937
Posted By TryHard

The ESC figures out the boost RPM range for...

The ESC figures out the boost RPM range for itself on the latest software... and does a pretty decent job of it too, in my opinon. Give it a try.

If you desperately want/need boost rpm control,...
Forum: Radio and Electronics
08-09-2014, 05:19 PM
Replies: 734
Views: 201,937
Posted By TryHard

That's because you can't program from the Rx...

That's because you can't program from the Rx wire. Only via the fan port.
Also, make sure the esc is plugged into a battery and switched on when programming.
Forum: Radio and Electronics
08-03-2014, 06:08 AM
Replies: 734
Views: 201,937
Posted By TryHard

Ran the new software on Saturday night, and did a...

Ran the new software on Saturday night, and did a back to back vs 129. Have to say, I preferred the feel with the new, seemed smoother, and more consistent on the brakes. Was a little concerned about...
Forum: Radio and Electronics
05-01-2014, 08:49 PM
Replies: 734
Views: 201,937
Posted By TryHard

They already are... 21.5 -...

They already are...

21.5 - http://roarracing.org/4rmb/showthread.php?297-Spec-21-5-Hobbywing-V10-Xerun-Stock-30401020049

17.5 -...
Forum: Radio and Electronics
04-10-2014, 06:00 PM
Replies: 734
Views: 201,937
Posted By TryHard

Those temps sound fine... I'd be shooting for...

Those temps sound fine... I'd be shooting for temps around 70-80C on that motor, with esc at about 90-100C (although I don't tend to look at esc that often).

You don't mention what FDR your...
Forum: Radio and Electronics
02-18-2014, 03:34 AM
Replies: 734
Views: 201,937
Posted By TryHard

Angelo means you need to load the V1.08_120504...

Angelo means you need to load the V1.08_120504 software onto your esc. Most of the softwares are shorted to the final three digits, hence "504". The names themselves are actually the dates.. so...
Forum: Radio and Electronics
02-10-2014, 04:19 PM
Replies: 734
Views: 201,937
Posted By TryHard

On the v3 you need to connect via the programming...

On the v3 you need to connect via the programming port. Connecting via the rx cable does nothing.
Forum: Radio and Electronics
11-14-2013, 04:27 PM
Replies: 734
Views: 201,937
Posted By TryHard

Honestly, not sure on this, never had an issue...

Honestly, not sure on this, never had an issue with the brakes on the V3.

Couple of things to check....
Set your reverse speed to 100%. I know you wouldn't be using reverse, but this can...
Forum: Radio and Electronics
05-22-2013, 06:36 PM
Replies: 734
Views: 201,937
Posted By TryHard

Agreed, IMO, high power (80w+) with a big tip are...

Agreed, IMO, high power (80w+) with a big tip are a must. Trick is to apply a lot of heat to a small area, quickly. A basic iron just won't cut it.
Does how how much heat the alloy case and heat...
Forum: Radio and Electronics
02-19-2013, 02:54 AM
Replies: 734
Views: 201,937
Posted By TryHard

Plug it into your PC, and open the software, but...

Plug it into your PC, and open the software, but on the menu bar, under Devices, put it to 'LCD program box'.
Forum: Radio and Electronics
02-18-2013, 05:38 AM
Replies: 734
Views: 201,937
Posted By TryHard

Deffiently check the plug connection on the box....

Deffiently check the plug connection on the box. Also, you might want to check what version of the program box software you have.
Forum: Radio and Electronics
02-16-2013, 05:04 AM
Replies: 734
Views: 201,937
Posted By TryHard

No Problems. Even though the software is saying...

No Problems. Even though the software is saying there is an update (it will take it up to USB link 3.2, from 3.1), best to manually download it from the site. So grab it off the site. The USB link...
Forum: Radio and Electronics
02-16-2013, 04:32 AM
Replies: 734
Views: 201,937
Posted By TryHard

Here you go.... There are 3 stages really....

Here you go.... There are 3 stages really. Software install, Update program box, update esc

Install Software
1) go to Hobbywing.com and download the latest firmware. Easiest just to follow this...
Forum: Radio and Electronics
02-16-2013, 02:45 AM
Replies: 734
Views: 201,937
Posted By TryHard

Thats a weird one... not got a dodegy RX...

Thats a weird one... not got a dodegy RX connection? or a shorting wire? Worth checking the simple things first :)
Forum: Radio and Electronics
02-16-2013, 02:43 AM
Replies: 734
Views: 201,937
Posted By TryHard

No offense dude, but thats bull crap. I know for...

No offense dude, but thats bull crap. I know for a fact that the V3 was tested a lot before release, including a full hard run at last years TITC by a large number of drivers.

Without trying to...
Forum: Radio and Electronics
02-16-2013, 02:35 AM
Replies: 734
Views: 201,937
Posted By TryHard

I think your not doing the calibration properly. ...

I think your not doing the calibration properly.
You need to turn your transmitter on (setting all values to 100% to get full calibration), then press and hold the button to get into the set mode....
Forum: Radio and Electronics
01-06-2013, 07:57 AM
Replies: 734
Views: 201,937
Posted By TryHard

If it's a V3, just attach the program box and...

If it's a V3, just attach the program box and switch to the the blinky profile (press 'R/P', then 'Value' to scroll through to mode 2). Whats neat is if you make changes to the stock blinky profile,...
Forum: Radio and Electronics
12-21-2012, 09:04 PM
Replies: 734
Views: 201,937
Posted By TryHard

Agreed, if it's not the usuals (sensor related),...

Agreed, if it's not the usuals (sensor related), check the LVC. The LVC is pretty sensative, and if you pull too much load out of weak batteries, it can cause the LVC to kcik in. I had this a number...
Forum: Radio and Electronics
08-29-2012, 06:14 AM
Replies: 734
Views: 201,937
Posted By TryHard

The ratio between boost and Turbo generally is...

The ratio between boost and Turbo generally is track dependent, although you will find that less boost will make the throttle smoother, when using a relatively short rpm range. Using less boost...
Forum: Radio and Electronics
08-28-2012, 08:10 PM
Replies: 734
Views: 201,937
Posted By TryHard

Does sound like you got a duff unit, as I'm quite...

Does sound like you got a duff unit, as I'm quite happily running 20+ boost and 20+ turbo with a 4.5. I wouldn't expect much difference for a 4.0 tbh. What was the gearing you were running? I use...
Forum: Radio and Electronics
08-28-2012, 08:04 PM
Replies: 734
Views: 201,937
Posted By TryHard

I'd recomend putting your start RPM higher......

I'd recomend putting your start RPM higher... more in the 5000-7000 rpm range, as the motor will never see 1500rpm round the track (except when starting from a dead stop!), so all your doing there is...
Forum: Radio and Electronics
08-27-2012, 05:19 AM
Replies: 734
Views: 201,937
Posted By TryHard

Out of interest.. what settings were you running?...

Out of interest.. what settings were you running? Only reason I ask is that to me the ESC seems to run cooler than others around, makes me wonder if the settings were outta whack a little.

Oh, and...
Forum: Radio and Electronics
08-05-2012, 02:26 AM
Replies: 734
Views: 201,937
Posted By TryHard

drop Angelo an email (CobraRacing on here), or...

drop Angelo an email (CobraRacing on here), or given your in the states, CRC or Falken Sadieko (they are the US distributors). All of them usually will give good service, so whilst I appreciate your...
Forum: Radio and Electronics
07-24-2012, 01:39 AM
Replies: 734
Views: 201,937
Posted By TryHard

I'm running a 1250MG in my car with Dualsky 4.5...

I'm running a 1250MG in my car with Dualsky 4.5 plus decent boost levels, no issues at all. Then again, also running a proper (ne Sanwa) radio system... :lol:
Showing results 1 to 25 of 26
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.