R/C Tech Forums - SC10 Thread

glue them to the block. The screws dont back out. The shim just gets squeezed out then the screw will seem loose because the shim is out.

little drop of glue on each end and bolt up....wont have a problem again.

:tire::tire:

Ae*Driver*70

10-11-2010 07:25 PM

AE Is Killer Of All......

Quote:

Originally Posted by T-BirdJunkie (Post 8057498)

Anti-squat shim?

Just used ballstud washers...wasn't even aware there were anti-squat shims. Do these come with the nifty new toe block thing?

NO ,ANTI SQUAT SHIMS COME IN THE OLD TOE BLOCK PACKAGES !:nod:

Ae*Driver*70

10-11-2010 07:28 PM

AE Is Killer Of All......

Dudes 3.5 Toe Block and 1* Degree Hubz !:nod::nod::nod::nod:
all you will need !

T-BirdJunkie

10-16-2010 07:32 PM

Anybody had any issues out of their STRC rear hubs? Got a little slop. FT ones going to be the same or better?

PIIHB!

10-17-2010 03:39 PM

Im looking to get aluminum rear carriers w/ 1* toe. Any recomendations? (integy, GH, STRC...)

PIIHB!

10-17-2010 03:40 PM

Quote:

Originally Posted by T-BirdJunkie (Post 8081416)

Anybody had any issues out of their STRC rear hubs? Got a little slop. FT ones going to be the same or better?

I was just looking at them on ebay. I couldn't imagine any more slop then the plastic ones.

T-BirdJunkie

10-17-2010 03:44 PM

Well, they've been in the truck for about 6 months, and admittedly they've taken a pretty gratuitous pounding...was just wondering if anybody had any experience with both.

ShortCourseOnly

10-17-2010 04:47 PM

Quote:

Originally Posted by PIIHB! (Post 8084417)

Im looking to get aluminum rear carriers w/ 1* toe. Any recomendations? (integy, GH, STRC...)

I have been using the STRC hubs. They have been fantastic. Love the bite and slop is minimum. Standard mounting.

That said I would switch to the AE FT hubs with the larger bearings just for durability. They look really good to me.

1Fastpede

10-17-2010 04:47 PM

i hear good raves about racers edge hubs

tennvol11

10-17-2010 05:04 PM

Quote:

Originally Posted by PIIHB! (Post 8084417)

Im looking to get aluminum rear carriers w/ 1* toe. Any recomendations? (integy, GH, STRC...)

I am a fan of Racers Edge as well.

mini696

10-19-2010 06:18 AM

I'm running an EZRun brushless setup in my SC10. Will 25C (50C Peak) LIPO's have enough current draw capacity?

Driver86

10-19-2010 06:58 AM

Quote:

Originally Posted by mini696 (Post 8092740)

I'm running an EZRun brushless setup in my SC10. Will 25C (50C Peak) LIPO's have enough current draw capacity?

I'm running an EZ-Run with a 5000mah 30C and the truck has more speed and punch than it can handle, so you're good.

mjk1210

10-19-2010 07:03 AM

Quote:

Originally Posted by Ae*Driver*70 (Post 8058320)

NO ,ANTI SQUAT SHIMS COME IN THE OLD TOE BLOCK PACKAGES !:nod:

I just bought a bag of toe blocks that had the shims in there. the bag had the blocks with 2.5, 3.0, 3.5, and 4 degrees of toe and it had shims for 1 and 2 degrees of antisquat.

mjk1210

10-19-2010 07:05 AM

Quote:

Originally Posted by PIIHB! (Post 8084423)

I was just looking at them on ebay. I couldn't imagine any more slop then the plastic ones.

try running on high bite clay with them a few times. HOLY SLOP :batman:

Ae*Driver*70

10-19-2010 07:49 AM

AE Is Killer Of All......

Quote:

Originally Posted by tennvol11 (Post 8084779)

I am a fan of Racers Edge as well.