R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: ByteStream
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: Radio and Electronics
12-21-2014, 09:28 PM
Replies: 734
Views: 201,938
Posted By ByteStream

What motor are you running? What do you have the...

What motor are you running? What do you have the endbell timing set at? For 17.5 TC 3.8 - 4.0 FDR works well for most motors. Your ESC seems a little warm but your motor seems like it's running hot....
Forum: Radio and Electronics
09-17-2014, 04:36 PM
Replies: 734
Views: 201,938
Posted By ByteStream

Starting Points .. 4.5T Andy Moore's setup...

Starting Points .. 4.5T

Andy Moore's setup (asphalt)
http://www.hobbywing.com/uploadfiles/sx/AppGuidance/Andy-Moore-1to10-2012IFMAR.pdf

Atushi Hara's setup (asphalt)...
Forum: Radio and Electronics
09-16-2014, 08:19 AM
Replies: 734
Views: 201,938
Posted By ByteStream

I'm not a fan of silver solder or mixes because...

I'm not a fan of silver solder or mixes because it takes alot of heat to get the solder to flow, which means the electronics take the brunt of it. Even with liquid flux, it's hard.

I've never...
Forum: Radio and Electronics
09-15-2014, 10:10 PM
Replies: 734
Views: 201,938
Posted By ByteStream

No, not possible to reverse the motor rotation on...

No, not possible to reverse the motor rotation on a V3.1

I'm not familiar with that kit, but some kits allow you to flip the gears to change direction of the transmission.
Forum: Radio and Electronics
09-15-2014, 10:02 PM
Replies: 734
Views: 201,938
Posted By ByteStream

I have assumed it was a silver solder blend due...

I have assumed it was a silver solder blend due to the amount of heat it takes to flow. I remove the stock solder with a braid and then use typical 60/40 which I still believe is the best option for...
Forum: Radio and Electronics
09-10-2014, 09:26 PM
Replies: 734
Views: 201,938
Posted By ByteStream

All programming requires the box.

All programming requires the box.
Forum: Radio and Electronics
07-31-2014, 08:44 AM
Replies: 734
Views: 201,938
Posted By ByteStream

Has the new software been sent to ROAR for...

Has the new software been sent to ROAR for approval?
Forum: Radio and Electronics
07-24-2014, 07:37 AM
Replies: 734
Views: 201,938
Posted By ByteStream

I've never seen a V3 HW ESC not want to enter...

I've never seen a V3 HW ESC not want to enter calibration mode. Only HW exception was very early releases of the 1S Xerun with V1 blinky software.

Can you perhaps post a video of what your doing?...
Forum: Radio and Electronics
07-24-2014, 07:06 AM
Replies: 734
Views: 201,938
Posted By ByteStream

I believe the program box is up to V1.17 .. but...

I believe the program box is up to V1.17 .. but will have to check and don't have my LCD box on hand (lent to a friend).

I would try to reinstall the ESC firmware if possible.

When you are...
Forum: Radio and Electronics
07-23-2014, 06:46 AM
Replies: 734
Views: 201,938
Posted By ByteStream

Which ESC are you using? Hold the power...

Which ESC are you using?

Hold the power button until you start to hear 'beeping' - usually 3+ seconds.
Forum: Radio and Electronics
07-22-2014, 08:17 AM
Replies: 734
Views: 201,938
Posted By ByteStream

Just to cover the basics .. 1. You should...

Just to cover the basics ..

1. You should have your program box connected to the PRG/Fan Port (not the RX plug).

2. The leads to the box/esc should be plugged in correctly +/- (this appears...
Forum: Radio and Electronics
07-22-2014, 06:58 AM
Replies: 734
Views: 201,938
Posted By ByteStream

Could be the order of the steps. 1. Start...

Could be the order of the steps.

1. Start the USB Link Software
2. Connect the ESC to the Computer via the programming box.
3. Turn the ESC on. (must be connected with batteries)
4. The program...
Forum: Radio and Electronics
07-12-2014, 09:41 AM
Replies: 734
Views: 201,938
Posted By ByteStream

The current version of the USB Link Software is...

The current version of the USB Link Software is v3.42 .. it is the program for your PC.

The current version of the LCD Box Software is V1.17

If you open the USB Link Software on your PC their...
Forum: Radio and Electronics
03-05-2013, 05:30 PM
Replies: 734
Views: 201,938
Posted By ByteStream

I really don't see trouble at all .. some user...

I really don't see trouble at all .. some user error issues, some questions on loading software or using the right software .. etc.

I would have recommended going through an authorized HobbyWing...
Forum: Radio and Electronics
12-21-2012, 02:27 PM
Replies: 734
Views: 201,938
Posted By ByteStream

Sounds like a bad sensor wire ... did you try...

Sounds like a bad sensor wire ... did you try with another wire?
Forum: Radio and Electronics
09-17-2012, 10:25 AM
Replies: 734
Views: 201,938
Posted By ByteStream

Just checking .. Are you using V1.1_120511_beta...

Just checking .. Are you using V1.1_120511_beta from the Version 3.1_120808 Package of software? That package is the latest.
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.