set up is as follows
esc reventon R
motor SP 10.5R 3.0
stock 0 v20
forward / brake no reverse ( have tried other set ups and yes reverse works perfect just no brake
lipo cut off : none
DRS :7
percentage braking: 100%
drag brake :10%
neutral range :2%
over heat: disabled



it is a brand new esc and motor and receiver
i have tried a known reciever out of my B4.2 and still the same
i have even used the same transmitter settings from my b4.2 and rebound to the speed passion stiil the same fault

in the 4PK i can see on a servo out put graph that brake signal is being sent to 120%

i have calibrated the radio to esc using both 100% and 120% EPA for both Th and Brake
no difference was seen

swapped and fitted in one of my HW v3 esc's and was the same found a dicky sensor loom ( pins wasnt crimped) ? while doing this
so fitted a new loom and the SP speedy and it is sweet
i dont understand how this would affect it ?
but its really nice now finally happy

i am greatfull for those that contributed to helping me fix this

No problem! Glad you got it working!! Have fun!

hi, everyone just got a 44.2 with the reventon pro [blue ] esc an have a tekin 7.5 motor. running on a 90 *120 feet track hard packed clay . what esc setup would be a good starting point? thanks

Here are some 4wd offroad setups.

http://www.speedpassion.net/us/escsetup.asp?t=5

Mod2? ,please can you tell me about this ,m just helping a friend ,first try out today its the new speed passion reventon club race 17.5 ,this is the same thing happen " no brakes" I ask him if theres any programmable card that comes with it but he said nothing ...so is there anyway that he can solve the issue ...besides the "programmable card" which is gnna cost him another thing ,please help ,thank you

Unfortunately I don't believe the Reventon Stock Club will support MOD2. Only the Reventon PRO, R, & S do.

What is the latest/greatest firmware for the Silver Arrow V2?

Looking for combo 17.5 what esc. Rev pro or the r worth the Xtra $$$$$ for 17.5 racing . Have pro with 10.5 In my buggy love that

I think there is only like 2 of them right?

I have a friend who has a reventon s and has no brakes in it. Is there something to get brakes in it? I believe he said it come with a programmer but still no luck.

I think the one that comes in it is the latest. It is just like the mod1 software. But older version.

Would like 2 put mod2 in my 4whl buggy but not sure how.. I have the reventon pro esc. Any help would be awosome...I have the interface downloaded in my laptop..

ok thank you for that information,so is there any other way beside the "programmable card" to get the stock club race esc going,cause theres no brakes ,please...

Hi all

Returning to sport after long break; hope you might be able to help with Speed Passion GT2.0LPF software questions.

Been onto SP website, got what I think is latest version of software for GT series (link from both ESC page and download page is same) and downloaded to laptop. Top link on page 2 of speed passion download pages, link at bottom of their site to it. (I can't post links as I'm new!)

Plugged LCD reader in and updated, plugged into ESC and it already has same code for software, previous owner had upgraded.

However; I see a lot of mention of 428MOD on SP website and forums, but LCD reader isn't displaying these numbers??

Exact messages I'm getting from reader are:

On power up: Speed Passion V1.07_110119
On clicking OK when connected to ESC: ESC Software Ver V3.0_110119_MOD

Am I using an older version or is this latest and 428MOD is just a shorter code for software version? Or have I got a more recent version than 428?

Any help appreciated; I've a few more questions which I could do with asking if you guys have time.

Thanks, Andrew (UK timezone!)