NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
#1651
#1652
Tech Elite
iTrader: (12)
Testamony!
I ran my Xerun 60A in my 1s 12th scale and I am completely sold on this ESC. Plenty of power, little to no heat and responds to settings. No Laptop needed thankfully!!! One tip for anyone that lacks punch out of the corner, check your total timing. Too much and all it does is rev really high but has ZERO torque. I turned down the timing on the motor to about 5-8 degrees and was a totally different beast.
#1653
#1654
Tech Apprentice
Im planning of getting a new lipo battery but currently im not sure if the esc or motor could handle it...
im thinking to use either a 3s 25-40C lipo or 2s 40-50C lipo on my HW Xerun 120A + 11.5T ...
please help
im thinking to use either a 3s 25-40C lipo or 2s 40-50C lipo on my HW Xerun 120A + 11.5T ...
please help
#1655
Tech Regular
iTrader: (20)
1s esc
Does anyone have a picture of a 12th scale with the 1s esc mounted. I read specs on the size however a picture would help. I am interested in installing this in a crc carpet knife 3.2r. I am just starting out in 12th scale and really have know idea. I running the 60a xerun in my Photon and like it. Is there a 60a 1s esc?
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
#1656
remember this anything lower than a 10.5t only 2 cell recommended
above a 10.5t like 13.5 etc 3 cell can be used
#1657
Does anyone have a picture of a 12th scale with the 1s esc mounted. I read specs on the size however a picture would help. I am interested in installing this in a crc carpet knife 3.2r. I am just starting out in 12th scale and really have know idea. I running the 60a xerun in my Photon and like it. Is there a 60a 1s esc?
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
I know this isnt going to be much of a help, but I can send you a photo of a 3.2 with a TC Sphere on it. The HW is even larger (about 6mm). Its a real tight fit with the Sphere, so the HW will be even tighter, but it will fit. I am ordering my HW 1S tonight. I am hoping to install it into my 3.2 in acouple of weeks. (assuming its taking 2 weeks to show up). Just think of all the space saves on not running a booster, or RX pack!
Shawn.
#1658
Does anyone have a picture of a 12th scale with the 1s esc mounted. I read specs on the size however a picture would help. I am interested in installing this in a crc carpet knife 3.2r. I am just starting out in 12th scale and really have know idea. I running the 60a xerun in my Photon and like it. Is there a 60a 1s esc?
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
I will post a picture tommorrow....
But, why don't you cut a piece of paper according to the dimensions and fit it in your car?
#1659
Tech Adept
Am I able to load the latest software eg:518stock or the 528mod onto the old XERUN 120A version 2.0 to use the supercharger option?
The hobbywing website seems a bit confusing as the version 2.1 only shows programable options 1-10 and no 12-15??? Even the picture is showing the version 2.0 when the description is for 2.1.
What is the difference between the version 2.1 and 2.0? I am referring to the XERUN 120A.
The hobbywing website seems a bit confusing as the version 2.1 only shows programable options 1-10 and no 12-15??? Even the picture is showing the version 2.0 when the description is for 2.1.
What is the difference between the version 2.1 and 2.0? I am referring to the XERUN 120A.
Last edited by chinaman; 11-25-2010 at 01:02 PM.
#1660
Can you run a 13.5T X12 with a 120a v2.0 without fan on esc? I'm asking because the f103 I have will not fit the esc between the decks with a fan mounted. Will be running 2S.
if yes,
Boosted/no boost an issue?
Thanks
if yes,
Boosted/no boost an issue?
Thanks
#1661
Tech Apprentice
thanks cobra for the advise...
#1662
#1663
Hi guys. Just got a V2.1. Is there any way to tell what software it has on it? Eg via the program box? What's the latest and best software to run with 17.5?
Cheers
Cheers
#1664
Does anyone have a picture of a 12th scale with the 1s esc mounted. I read specs on the size however a picture would help. I am interested in installing this in a crc carpet knife 3.2r. I am just starting out in 12th scale and really have know idea. I running the 60a xerun in my Photon and like it. Is there a 60a 1s esc?
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.
Thanks any info on 12th scale would help. I plan on running a SP(sorry) 17.5 v3 motor.