Go Back  R/C Tech Forums > Members List
Reload this Page >



Tech Elite

Visitor Messages

Showing Visitor Messages 1 to 10 of 43
  1. Ranger29
    07-27-2017 05:49 PM - permalink
    Hey I have a question for you if you don't mind helping me out I would greatly appreciate it, I have a HW xr8plus and a hw 2250kv motor, everything's Hooked up and calibrated but when I squeeze the throttle the esc light will turn red until I let off the throttle. Is that normal? I ran it today and noticed that....it feels ok but I don't have to much experience with this hobby, I'm running it in a tekno mt410 with SMC 4s battery and futaba 3pv radio. It turns red when I brake as well. Shouldnt it turn green when i throttle it? Or is red correct?
  2. fox947
    04-17-2017 09:11 PM - permalink
    Hi, have a Xerun 4000 kv 4pole brushless motor with a bad bearing at the sensor end of the motor . When you remove that end of the motor the end cap is solid so you can`t tap the bearing out. How do you get the bearing out to replace, is there a special puller. Thanks pete
  3. conbuomxinh
    09-16-2016 02:59 AM - permalink
    Nguyên bản, hắn định chuẩn bị sắp tới, t́m một cơ hội phái tên đệ tử đó ra ngoài cho bớt phiền toái.

    - Có Băng phôi mới hay chưa?
    dịch vụ kế toán trọn gói giá rẻ
    dich vu so sach ke toan
    dịch vụ báo cáo thuế
    dịch vụ báo cáo tài chính cuối năm
    dịch vụ kế toán thuế trọn gói

    Vương Lâm chắp tay sau lưng, nói một cách chậm răi. Băng phôi là cách gọi của tu sĩ Tuyết Vực đối với băng điêu.

    Tên nhị đệ tử vội vàng cung kính nói:
  4. fastalarid
    03-01-2015 06:53 PM - permalink
    Have a question 3.1 1s esc I was told it should blink green not red to be in blinky mode. Thanks
  5. GavinR2D2
    11-15-2014 08:25 AM - permalink
    Hi Angelo, I was given your name by someone on RCTech. I hope you don't mind me contacting you. I've just purchased a v3.1 hobbywing speedo and I'm in the process of updating the firmware. Unfortunately, when I try to download from the HW website, both the links for the '2 in 1 prog box' and speedo are broken.

    Would it be possible for you to send me the firmware updates I need?

    Any help in the matter would be greatly appreciated.

    Kind Regards

  6. omen1975
    05-11-2014 08:29 PM - permalink
    Hi, Can you please inform me of the address I will need for Hobbywing repairs? cheers.
  7. to slow for you
    05-11-2014 09:41 AM - permalink
    problem after update try program through box says need to upgrade software has both the box and esc update but can use pc ?
  8. snip3r66
    01-18-2014 06:25 AM - permalink
    I am using HW V3.1 and running MuchMore Fleat ZX 13.5T boosted. My FDR is 6.0 (28 pinion and 84 spur)
    I don't seem to be able to get much power on the straights. 13.5T blinkies can over take me on the straights.
    Any suggested settings to the ESCs or suggestions on change the FDR?

  9. sonspit
    11-01-2013 08:49 AM - permalink
    I have the 150a xerun esc using firmware V103_130806_Beta

    I am trying to upgrade or downgrade to firmware V1.00_111207a_2R

    so I will not have compatibility issue with my tenshock motor

    but the link is telling me beta cannot be updated to this version.

    why is that?

    can u help me?
  10. 62 Swag
    04-15-2013 10:43 AM - permalink
    can you clarify the difference between the sct pro and the v2.1 esc for me?

About Me

  • Signature
    Email : [email protected] or [email protected]
    Repair service Address
    Hobbywing Technology Co., Ltd.
    4th Floor, 3rd Building, KeLunTe Industrial Park, ShangLiLang, BuLan Road, LongGang District, ShenZhen, China


Total Posts
Visitor Messages
General Information
  • Last Activity: 10-26-2018 01:10 AM
  • Join Date: 11-12-2007
  • Referrals: 0


Showing Friends 1 to 6 of 6

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service