Tamiya TA05 Touring Sedan
#8598
Hi All
Does anyone know the specs of the new TA05RR coming out ?
49418 TA05-RR CHASSIS KIT 29800YEN JAN ( off Rainbow ten )
Thanks
Does anyone know the specs of the new TA05RR coming out ?
49418 TA05-RR CHASSIS KIT 29800YEN JAN ( off Rainbow ten )
Thanks
#8599
#8601
Tech Initiate
TA05 Questions
I bought one of these off of ebay, and have some questions which I can't find answers for in either the documentation of the manual or as a reply in this thread.
1. My car came with a center one way, and I'd like to convert this to a standard layshaft, because I'd like to run this car with a solid axle in the front. So what parts do I need to make this happen?
2. I'd like to be able to change the rear toe in from anywhere between 0.5 degrees and 3.0 degrees, depending on the surface condition. Since this car doesn't use spacers like an Xray, I'm guessing I need either multiple suspension holders of different widths or different rear hubs. So what are the parts I need to make changes to rear toe in?
3. I noticed this car has pretty limited steering throw, about 10 degrees for the outside wheel and 15 degrees for the inside wheel using maximum ackerman. It seems to be limited by the turnbuckle ball end touching the bellcrank steering arm at maximum extension. Is there a way to get greater steering throw on this car?
1. My car came with a center one way, and I'd like to convert this to a standard layshaft, because I'd like to run this car with a solid axle in the front. So what parts do I need to make this happen?
2. I'd like to be able to change the rear toe in from anywhere between 0.5 degrees and 3.0 degrees, depending on the surface condition. Since this car doesn't use spacers like an Xray, I'm guessing I need either multiple suspension holders of different widths or different rear hubs. So what are the parts I need to make changes to rear toe in?
3. I noticed this car has pretty limited steering throw, about 10 degrees for the outside wheel and 15 degrees for the inside wheel using maximum ackerman. It seems to be limited by the turnbuckle ball end touching the bellcrank steering arm at maximum extension. Is there a way to get greater steering throw on this car?
#8602
I THINK THIS IS THE IFS NSX
If you look at the wheel wells there is a difference than the prev. NSX's
#8603
That's cool.
The older (2005 and below models) SuperGT NSX doesn't look as low as the current model. The 2005 (?) ARTA NSX I had on my TA05 used the lowest holes on the body posts, so scale replicas of new lower profile NSX aren't possible to use properly without the IFS setup.
The older (2005 and below models) SuperGT NSX doesn't look as low as the current model. The 2005 (?) ARTA NSX I had on my TA05 used the lowest holes on the body posts, so scale replicas of new lower profile NSX aren't possible to use properly without the IFS setup.
Last edited by HI_808; 11-19-2007 at 10:31 PM.
#8604
3. I noticed this car has pretty limited steering throw, about 10 degrees for the outside wheel and 15 degrees for the inside wheel using maximum ackerman. It seems to be limited by the turnbuckle ball end touching the bellcrank steering arm at maximum extension. Is there a way to get greater steering throw on this car?
Layshaft question should be answered with a look at a manual. Toe in is changed by blocks but it depends a little on what suspension parts the car is running.
#8605
http://www.tamiya.com/english/rc/rcmanual/ta05.pdf
I have a lightweight centre shaft, it saves a few g if you want to buy that instead, the p/n is 53915.
hth
#8606
Tech Initiate
Heres a link to the manual, all the part numbers should be in it for you to change back to stock parts
http://www.tamiya.com/english/rc/rcmanual/ta05.pdf
I have a lightweight centre shaft, it saves a few g if you want to buy that instead, the p/n is 53915.
hth
http://www.tamiya.com/english/rc/rcmanual/ta05.pdf
I have a lightweight centre shaft, it saves a few g if you want to buy that instead, the p/n is 53915.
hth
#8607
Can anyone tell me if this part will fit my ta05 please?
http://shopping.rcmodel.hk/product_i...oducts_id=5562
If it doesnt ah well, at least i've got an expensive paperweight in the post LOL
http://shopping.rcmodel.hk/product_i...oducts_id=5562
If it doesnt ah well, at least i've got an expensive paperweight in the post LOL
#8608
Tech Elite
iTrader: (41)
I don't THINK so...but you might be able to adapt it.
Here's a TA05 adapter.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNZB3
Here's a TA05 adapter.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNZB3
#8609
I don't THINK so...but you might be able to adapt it.
Here's a TA05 adapter.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNZB3
Here's a TA05 adapter.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNZB3
#8610
Square has also complete Sets of Titanium Screws (für TA05, TA05R and TA05IFS). These screws are 100% identical to the Tamiya ones.
More Info on http://www.rc-square.de/english/squa..._ta05-tb02.htm
More Info on http://www.rc-square.de/english/squa..._ta05-tb02.htm