4LikesViper RC -
10-02-2012 | 01:24 PM
#5596
Suspended
Joined: Jul 2011
Posts: 20
I just wanted to post one last time here. I had a viper system VTX10R and was having issues. It locked and i was unable to fix the issue my self. I was unable to rum the main because of it. So, i posted on here for help, Vipers FB page and sent an email from there support page on Viper .com. I have received more support from my fellow members here than i did from Viper support. Sadly, what advice i did receive(None from the email at all, One from the FB page and one from here) was amatuer at best. VERY dissatisfied with Viper. I have no faith in there ESC nor customer support, but do like the motors. I pitched the ESC and am now back with Tekin.. I had herd good thing from fellow recers about Viper but my experiences have left me sour!
10-02-2012 | 01:59 PM
#5598
Joined: Jun 2008
Posts: 5,071
10-03-2012 | 04:03 AM
#5601
I just wanted to post one last time here. I had a viper system VTX10R and was having issues. It locked and i was unable to fix the issue my self. I was unable to rum the main because of it. So, i posted on here for help, Vipers FB page and sent an email from there support page on Viper .com. I have received more support from my fellow members here than i did from Viper support. Sadly, what advice i did receive(None from the email at all, One from the FB page and one from here) was amatuer at best. VERY dissatisfied with Viper. I have no faith in there ESC nor customer support, but do like the motors. I pitched the ESC and am now back with Tekin.. I had herd good thing from fellow recers about Viper but my experiences have left me sour!
10-03-2012 | 04:06 AM
#5602
I myself run Futaba radios (604 Receivers and 614) and have had no issues with my Savox 1257 and 1258 servos.
10-03-2012 | 11:00 PM
#5604
When using HV servos, you need to make sure the receiver can handle the voltage and amp draw. Some RX are not meant to be used with high powered servos and will throw them into failsafe mode. Just make sure you look at the receivers specs before using HV servos and you will be fine
10-04-2012 | 05:35 PM
#5607
10-04-2012 | 10:10 PM
#5609
Just wanted to give everyone some updates from Viper and the team:
If you follow on road racing you know the International Indooe Champs are being held this weekend. Our newest recruit Multi-time National Champion Josh Cryul has jumped right in with two 2nd place finishes in WGT and 1/12 Modified. Mark Smyka is top 5 results in 1/12 17.5 as well.
Some offload team members will be attending the J Concepts Northeast Championships this weekend at RCE in MA. We had a great event their last year and looking for good results this weekend.
And finally, we want to wish our very own Dave Beam good luck as he is getting married this weekend -- congratulations!!!
If you follow on road racing you know the International Indooe Champs are being held this weekend. Our newest recruit Multi-time National Champion Josh Cryul has jumped right in with two 2nd place finishes in WGT and 1/12 Modified. Mark Smyka is top 5 results in 1/12 17.5 as well.
Some offload team members will be attending the J Concepts Northeast Championships this weekend at RCE in MA. We had a great event their last year and looking for good results this weekend.
And finally, we want to wish our very own Dave Beam good luck as he is getting married this weekend -- congratulations!!!
10-05-2012 | 02:41 AM
#5610
I need to relocate the caps on my VTX10 so I can shove the esc underneath the rear bulkhead on my new RB6. Are there any issues with desoldering the board and hanging it off on a wire? Specifically maximum wire length?