R/C Tech Forums - Viper RC -

There is a 2 day turn around time for firmware upgrades. For example if you send it in Monday morning we will be shipping it out tuesday afternoon. If you have PC link wire then i can send you the firmware and the program to upload into the ESC, its a 2 step process :)

Hi I have a pc link can u pls send me firmware and program so I can upgrade my viper
Thank you Jim I will pm u my email address

ekim628

11-30-2011 01:22 PM

Quote:

Originally Posted by jimkoimanis (Post 9976371)

Hi I have a pc link can u pls send me firmware and program so I can upgrade my viper
Thank you Jim I will pm u my email address

You Have mail :)

So*Cal AFDude

11-30-2011 05:17 PM

Just wanted to make sure that http://eazyrc.com/viper-brushless-rc...p-torque-rotor <- that rotor will fit in a 17.5 motor. Also if anyone has tried it, what were the results ... Thanks :D

Jumpinj

11-30-2011 05:18 PM

How important are the firmware updates? I am running three systems and sending them in would not be so fun.

nikos2002

11-30-2011 07:28 PM

They are helpful but not 100% necessary. The are a few updates to the calibration, and Smart Braking system (Dynamic Braking). Send them back one at a time, the turn around is pretty quick.

nikos2002

11-30-2011 07:30 PM

Quote:

Originally Posted by So*Cal AFDude (Post 9979438)

Just wanted to make sure that http://eazyrc.com/viper-brushless-rc...p-torque-rotor <- that rotor will fit in a 17.5 motor. Also if anyone has tried it, what were the results ... Thanks :D

it will fit... I have tried it in a 17.5, our motors are pretty torquey to begin with. Maybe if you race at a really small track.

So*Cal AFDude

11-30-2011 07:54 PM

Quote:

Originally Posted by nikos2002 (Post 9980063)

it will fit... I have tried it in a 17.5, our motors are pretty torquey to begin with. Maybe if you race at a really small track.

Thanks for the reply. I'm thinking it will be able to be geared to the moon with this combo. Or would over heating still be a factor?

nikos2002

11-30-2011 09:44 PM

So*Cal - it might be hard to do if you are running the SC I think you are - the gearing options are kinda limited. Good thought, but it might be all bottom end and no top - depends on the type of track (layout, etc). I actually wanted to try the RPM rotor with it - but I only rarely run 17.5.

So*Cal AFDude

11-30-2011 10:08 PM

Quote:

Originally Posted by nikos2002 (Post 9980642)

It will actually be going in my Dads SC10. It's a med. size out door dirt track HCR/ Palm Desert/ Thunder Alley. Going to be running no timing and no boost on the esc as well.

ekim628

11-30-2011 11:02 PM

Quote:

Originally Posted by So*Cal AFDude (Post 9980698)

It will actually be going in my Dads SC10. It's a med. size out door dirt track HCR/ Palm Desert/ Thunder Alley. Going to be running no timing and no boost on the esc as well.

In my opinion at those track you mentioned, you should leave stock rotor or pop in a high RPM rotor and gear up. The VST motors especially the 17.5 already have enough torque to play with. Just my opinion

olegeezer

12-01-2011 04:17 PM

i sent in in a vtx10 for repair how would i get the firmware update didn't mention on rma what phone # do i call.thanks lance

tcrain

12-01-2011 06:23 PM

May be posted and I just missed it but is there a release date for the vtx1 yet?

All times are GMT -7. It is currently 11:19 AM.

Page 214 of 805