|
Originally Posted by Motorman007
(Post 13359493)
I read everything I could on this and still will not get the green light when I try to calibrate. Everything seems work.
Pullback hit the button Push forward hit button Let go all lights do its thing Green like flashing after I also hooked up other motor And other sensor wire. I flashed the A64, many times. Radio 10 clicks - /+ Anymore ideas. Before I send it in? Then I did the same thing to my tekno truck same 1/8 esc vtx8 and it calibrate. -Try same model you calibrated your tekno on? You can always send it in, just hate when someone sends something in and we can't find anything wrong with it. Just trying to make sure. |
Originally Posted by boborc
(Post 13360693)
Also whats the ETA in the VF4's I see their out of stock. See what happens when I snooze. should have gotten one a couple of weeks ago:cry:
|
Originally Posted by carguy83
(Post 13359972)
I think I'm going to leave my stock setup alone and work on my driving skills.
|
Originally Posted by boborc
(Post 13359512)
Thinking of getting a vf4 for a sc10 4x4. What rpm/kv do you recommend 4k 0r 4500. Med-large tracks. Have a 4.5 ballistic which is good but need a little more launch. Have a budget 4 pole 4800kv seemed a little overkill on the med track and is also undependable (shabby bearings keep going). The ballistic is rated 5k per kv so should I go with the higher or just a little more gear in the lower kv (slippery tracks for the most part). The large track has a 3/4 oval for the straightaway (its big). Thanks
|
It was letting me backorder if I wanted.:nod: I'll place an order for a 4500 tomorrow. Have some home projects this weekend so no racing for me anyway:cry: Hopefully next week:)
|
Originally Posted by boborc
(Post 13360880)
It was letting me backorder if I wanted.:nod: I'll place an order for a 4500 tomorrow. Have some home projects this weekend so no racing for me anyway:cry: Hopefully next week:)
|
Originally Posted by nikos2002
(Post 13360761)
.
-Try different model on your radio? -Try same model you calibrated your tekno on? You can always send it in, just hate when someone sends something in and we can't find anything wrong with it. Just trying to make sure. -Try same model you calibrated your tekno on? I did that sir nothing. -Try different model on your radio? This I have not tried Will do it now thank you sir. HERE IS THE VIDEO I JUST DID
|
|||||
Originally Posted by nikos2002
(Post 13360901)
He's a man with a plan!!
|
I have been running a 4500 copperhead combo in my ten scte and seems I can not keep my temps down I am currently running a 15 tooth pinion with stock spur and yesterday after the 6 min main my motor temps where reading 185! I really don't want to drop pinion size again. But I am really taxing this motor, I have had esc overheat kick in twice before dropping my pinion down. This is the second motor as a warranty replacement . I never had these issues prior to that could this motor be less efficient ? Or will I need to move up to the vf4/vtx8 to get decent run times? Thanks
|
I should also mention that both esc overheats happened after a crash, unread somewhere in the forums that an arc from the bullet connectors could cause the system to read esc overheat , is this the case ? Also would any of the new high voltage fans run better on my esc? Mine will sometimes hang up durring start up.
|
Where are your settings at? Like punch, start power and timing? I usually never run any of these over 5.
|
Also, what type of track and how big? A 15 tooth for an SCTE would imply a pretty big track. I don't ever gear to a 15 with my SCTE.
|
Just picked up a vtx8 for my sct410. Trying to figure out if I need the PC link for anything other than updating the firmware on the esc. I have the progauge and hoping I can get to all the settings. My friend has the link so figuring I could just use his for updating. Thx for any info.
|
Yup, you don't really need the link for anything other than updating unless you want to be able to save out and/or update setups to your computer. Having a buddy with one of these is NICE....
|
Originally Posted by DustinH
(Post 13367807)
Where are your settings at? Like punch, start power and timing? I usually never run any of these over 5.
|
| All times are GMT -7. It is currently 10:36 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.