|
Ok so lets see...
The weather in that weekend race will be cold without sun... The race truck, is kind of open some quick parts, but not easy... So for sure Ill some more steering and the car has to be quick from corner to corner!! Should i use purple springs with 450 silicone front and behind?? |
Xray batts
Hi
im waiting for my first nt1!!, can you guys recommend me an specific model of batt for the rx (life or lipo)? Any start up list of spares>? or hop ups? thanks! |
i have tried Li-fe batteries for my NT1 but they are normally too long to have a perfect fit in size. Normally, my friends will cut off the protection plastic packing in order to put the battery in place. Better choose either Li-po (but you then require a voltage regulator) or the usual NIMH battery.
|
Originally Posted by Yoshimon
(Post 9814588)
i have tried Li-fe batteries for my NT1 but they are normally too long to have a perfect fit in size. Normally, my friends will cut off the protection plastic packing in order to put the battery in place. Better choose either Li-po (but you then require a voltage regulator) or the usual NIMH battery.
flattened the north and south corner of xray battery holder. north corner [___________li-fe battery__________] south corner |
Originally Posted by gaspar
(Post 9814499)
Hi
im waiting for my first nt1!!, can you guys recommend me an specific model of batt for the rx (life or lipo)? Any start up list of spares>? or hop ups? thanks! |
Originally Posted by staikosn1
(Post 9798074)
Ok so lets see...
The weather in that weekend race will be cold without sun... The race truck, is kind of open some quick parts, but not easy... So for sure Ill some more steering and the car has to be quick from corner to corner!! Should i use purple springs with 450 silicone front and behind?? |
Originally Posted by bluer322
(Post 9815107)
Ues the Exceed lipo pack fits perfick.
do i need a regulator? do you have the model number? thanks!1! |
Originally Posted by gaspar
(Post 9815569)
Hi
do i need a regulator? do you have the model number? thanks!1! Li-PO part number 105001 Voltage Regulator 105002 |
I ran the 2011 Spec today.....W/every mod!..LOL! It is a 2 day Event......We ran 3 qualifiers... currently im sitting at TQ.....Donnie Thomson 23 laps.....5:12.856 running the 2011 spec,with Sirio Mills and pipes,savox servo's this is a AWESOME hotrod.....:nod::tire::tire: Xray pilot....Jason Lutz........22 laps..........5:11.360 . Xray Pilot....Lee Thompson....21 laps.........4:59.887 Privateer......Kevin Stephens...21 laps.........5:09.183..... we sdtill have another qualifer and the mains tomorrow... Wish Me luck.... |
Originally Posted by Factory Seal
(Post 9816558)
I ran the 2011 Spec today.....W/every mod!..LOL! It is a 2 day Event......We ran 3 qualifiers... currently im sitting at TQ.....Donnie Thomson 23 laps.....5:12.856 running the 2011 spec,with Sirio Mills and pipes,savox servo's this is a AWESOME hotrod.....:nod::tire::tire: Xray pilot....Jason Lutz........22 laps..........5:11.360 . Xray Pilot....Lee Thompson....21 laps.........4:59.887 Privateer......Kevin Stephens...21 laps.........5:09.183..... we sdtill have another qualifer and the mains tomorrow... Wish Me luck.... |
Originally Posted by rx7ttlm
(Post 9815301)
I would start with ralph burch's winternats setup and adjust from there.
All racers had problems cause we had to get used to the new truck line (if I say it correct) THe car was good enough, I changed the suspensions positions more to vertical (minor change, but finally so big) , the R3 RC was to quick, and i had to loose the centax spring a 1/4 of hour... I used 37-40 tires, but next time Ill use 35-37 for better grip... I have to admit that i didnt change the silicone in diffs for the race.. I ll do it next time!!!! I started 4th in 2nd final...I finished 3rd, and took place place for 1st final... Was last in 1st final in 14 cars,and i finished 8th!! 1,5 hour of racing this weekend, perfect for practice!!! Cheers, Nick! |
could you please tell me what your track is built out of
|
the Track is built from 3inch plastics PVC,we make T's inserts,small curves and big,,and Bend at different angles...drill holes in the ends for strapping it together...we also use Plow disc with a slot for the pipe to fit in for stops fo sharp corners.....and lots of VHT!....LOL!
......loop is 4inch pipe.....Drivers Stand is 13ft off the ground and 30ft in length.........:tire::tire:. |
Actually it's 2.5" PVC conduit schedule 40.
The connectors are 2" sch. 40 PVC conduit with a small 2.5" sleeve in the center. BTW Donnie- that guy smiling in the picture u posted is one handsome fella. He musta won? :lol: |
| All times are GMT -7. It is currently 05:51 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.