RL.2002

Thankz mate.

TBOTubed

Thank You too

mos-leung

Which program card used? LCD card from HW or LCD card from SP ?

razzor

either one will work.

mos-leung

i just downgrade my HW LCD to SP 1.02.

Hatebreed

just ordered myself a xerun 120 sd blue esc, how does the esc handle a 3.5 motor? will it go poof or is it ok? i will run a high speed fan on it.

its going to handle a 4.5t motor most of the time but our asphalt track is so large that i think that a 3.5 could be drivable even with 2s lipo.

razzor

it will handle it. One of the very few esc's that can handle down to 2.5 reliably.

TBOTubed

anybody have a look at the new HW update?
http://www.hobbywing.com/english/downloads.asp

100422 for stock w/ dynamic timing and turbo function

sammies

iTrader: (1)

Interesting... anyoen tried it yet??

Will it work on a Seed Passion GT?

geubes

looks like that download includes all the Beta stuff sofar including 410, and a 422???

anyword from HW as to where this has come from and why they chose to release it on the site? another supercharge/turbo break through?

mos-leung

I'm new user of HW XERUN 120A.
May i know what the software are ? i mean from SP or HW software....?
Also, Which LCD card /software used for upgrade the ESC? from HW or SP?

unsp0ken

iTrader: (25)

Anyone know where I would be able to get replacement switches for the Xerun?

Born2Run

You can cut the switch wires and solder this one:http://cwactionhobbies.com/esc-onoff...ss-p-8540.html

TBOTubed

Loaded new 100422 into my speedo and found the following;
After installing all settings must be done with the orignial setting box
#4 drrs 1-6 n/a
#15 SC punch 7-8 n/a
It feels smooth with a bit of punch (can only bench test because of the rain)

The bummer is that I can not down grade to older versions. I tried with V1.02 and V103-090704 in my lcd to bring it back to 110 or 324 and no happiness.
(WOOPS GOT IT SORTED) Downgraded with HobbyWing USB Link 1.5 then reloaded 110 and 230 and back to 422
Any ideas
windows xp

steliosh

I also loaded the new 1.6 HW software. First of all, I did upgrade from 1.02 to 1.04 091225. The softwares included are V1.10 205_mod, V2.0 100422_stock and (an older, I presume) V1.10 323a.
I installed the 422 stock to my Xerun 60A (running a Nosram 13.5T), on my KP09 motorcycle, set it at the basics, as per SP's earlier pdf (since HW won't give us any instructions!), and ran the bike at a local parking lot.
Mind you this update also kept saying to me "Please upgrade software", so I did everything twice, just to be sure!

At first it lagged a bit, then wheelied a couple of times, when it found good traction! but most of the time just span its rear wheel, when the SC came on rather abruptly, reminding me of old turbocharged cars (like the MK1 Fiat Punto GT I used to own years ago!). The bike is geared rather on the long legged side... at FDR 6.94, while I have been advised to go a bit longer as well to 6.69.

Anyway, I played with the settings a bit and came to a first conclusion a what MIGHT work for the bike, at least:
1. 1
2. 3
3. 5
4. 5 (when I had this at 7, there was lag... so I started lowering it)
5. 4 (and played with ATL from Tx)
6. 1
7. 1
8. 1
9. 7 (22.50*)(while it started default at value 4, eg. 11.25* timing)
10. 1
11. 1 but it doesnt matter, I guess
12. 8 (it was mid level, but not good, I incremented this one step a time)
13. 3 (I ran out of batteries and didnt test this any lower number, I d like to see what it does at 1 and 2)
14. 1 (off)
15. 1 (and I closely observed for overheating, but the motor was always good to touch for at least 5 sec - I forgot my temp gun at home!)

So far so good, the bike wheelied at least three times, probably at some places the traction was better, the throttle response was linear, a couple of times it did me some cogging when starting from dead, I pushed the sensor cable at the motor end in and it quit doing it! (I may need a new cable just in case). the top speed was spectacular, the mid to top was also very very good and what impressed me most was the linearity. With the bikes you NEED this feature, especially when the bike is leaned over and you start pushing the throttle, you don't want it to step sideways, highside and tumble. The "turbo lag" is not gone at all, but it's minimal and I will do some more testing at the track, this time...
My local track is quite huge, with three large straights (60m, 48m, 35m), so the parking lot was not that different!

I have not yet installed it in my son's Sprint2 RCGT which runs a 60A Xerun and a Nosram 17.5T, but that will have to wait till the end of May race...
I also installed the 205 version from the HW422 in my Losi XXXSG, running a Xerun 120A and a 5.5.T motor, and ran a few minutes to check that it was going straight. It is also linear but care must be paid here: By default it gives max AMTS at 26.25*!!!! I duly reduced that to 11.25*, of course!