XERUN V2.0 Brushless ESC discussion thread.
#601
#602
Tech Apprentice
which version of sp ultrasportsman did you use ? i heard the first version (faigao) have cooler temp on sp supercharger
these are the settings i used with 410 on friday night at hrcc in ware. a small/medium indoor carpet track.
speed passion gt2.0pro
speed passion 13.5 ultrasportsman
fdr 78/24 internal ratio 2.4375
temp after 5mins 50degrees
1-1
2-3
3-4
4-9
5-3
6-1
7-1
8-1
9-5
10-1
11-1
12-7
13-1
14-1
15-3
not too bad, on the straight didnt kick in till half way down,couldnt get it to come in any sooner. good in the infield though.
speed passion gt2.0pro
speed passion 13.5 ultrasportsman
fdr 78/24 internal ratio 2.4375
temp after 5mins 50degrees
1-1
2-3
3-4
4-9
5-3
6-1
7-1
8-1
9-5
10-1
11-1
12-7
13-1
14-1
15-3
not too bad, on the straight didnt kick in till half way down,couldnt get it to come in any sooner. good in the infield though.
#603
Tech Apprentice
v324 firmware
i was running 324 firmware with fdr 7 on a big track and having 1 to 1.5 seconds discrepancy lap time compare to tekin rs pro with fdr 6.5
perhaps next time i'll reduce the drrs to gain more top speed + adding a bit of infield punch
ps: we're both use the same sp v3.0 11.5T motor
4:8
9:5
12:6
13:5
14:5
15:6
perhaps next time i'll reduce the drrs to gain more top speed + adding a bit of infield punch
ps: we're both use the same sp v3.0 11.5T motor
4:8
9:5
12:6
13:5
14:5
15:6
#604
these are the settings i used with 410 on friday night at hrcc in ware. a small/medium indoor carpet track.
speed passion gt2.0pro
speed passion 13.5 ultrasportsman
fdr 78/24 internal ratio 2.4375
temp after 5mins 50degrees
1-1
2-3
3-4
4-9
5-3
6-1
7-1
8-1
9-5
10-1
11-1
12-7
13-1
14-1
15-3
not too bad, on the straight didnt kick in till half way down,couldnt get it to come in any sooner. good in the infield though.
speed passion gt2.0pro
speed passion 13.5 ultrasportsman
fdr 78/24 internal ratio 2.4375
temp after 5mins 50degrees
1-1
2-3
3-4
4-9
5-3
6-1
7-1
8-1
9-5
10-1
11-1
12-7
13-1
14-1
15-3
not too bad, on the straight didnt kick in till half way down,couldnt get it to come in any sooner. good in the infield though.
9-6
12-6
13-5
14-6
15-3
also you can try a tooth or 2 bigger on the pinion.
#606
with your settings above, wouldnt the supercharger kick in later? only i need it to come in sooner.
if any one can help, please look at my picture. i belive its the v.1 ultrasportsman. maybe its more to do with my motor than speedo/settings?
yeah, just looked at the motor its got FEIGAO written on it. does that mean its version 1?
Last edited by xrayal; 04-18-2010 at 02:54 AM.
#607
Victory with 324
Today I tried the software 324 in the race, race club as good as warm up the Italian league, class 17.5 with excellent results
TQ and victory in the final A.
Performance was on a par with other competing ESC, Tekin, LRP SXXSS, Mamba Max and engine temperatures always constant at 60/65C° with environment temerature 20/22C°.
I am very happy with this 324
You can see the track here:
http://www.laurenziana.it/modellismo/
TQ and victory in the final A.
Performance was on a par with other competing ESC, Tekin, LRP SXXSS, Mamba Max and engine temperatures always constant at 60/65C° with environment temerature 20/22C°.
I am very happy with this 324
You can see the track here:
http://www.laurenziana.it/modellismo/
#608
i tried 26 pinion, it was too much, still accelerating and getting to hot.
with your settings above, wouldnt the supercharger kick in later? only i need it to come in sooner.
if any one can help, please look at my picture. i belive its the v.1 ultrasportsman. maybe its more to do with my motor than speedo/settings?
yeah, just looked at the motor its got FEIGAO written on it. does that mean its version 1?
Attachment 581635
with your settings above, wouldnt the supercharger kick in later? only i need it to come in sooner.
if any one can help, please look at my picture. i belive its the v.1 ultrasportsman. maybe its more to do with my motor than speedo/settings?
yeah, just looked at the motor its got FEIGAO written on it. does that mean its version 1?
Attachment 581635
It would labour the motor and make it flatter than what it could be.
Try get a setup good for the slow section of the track with out running supercharge. when happy then engage supercharge for that extra speed on the straight.
supercharge is not for running all the time only for the faster sections of the track.
AMTS has a influence on punch and needs a lower setting for more rip and the supercharge will give the extra rpm needed at top speed.
#609
thanks mate, ill try your settings this friday.
c2b, theres a memorial meeting at wlrc this bank holiday monday.if youve not raced here before your missing out big time, fancy coming down with a couple of the maritime boys???????????? lets give those tekin gm spxx boys a run for their money lol. there will be at least 7-10 from our local club night going down there, it will be a really good day, spread the word mate
c2b, theres a memorial meeting at wlrc this bank holiday monday.if youve not raced here before your missing out big time, fancy coming down with a couple of the maritime boys???????????? lets give those tekin gm spxx boys a run for their money lol. there will be at least 7-10 from our local club night going down there, it will be a really good day, spread the word mate
#610
It has happened a few times with my futaba PCM 40Mhz, using the XE120A erun with mod motors (std software), both in buggy (6.5T) and TC (5.5T)...
I am going to revert to 2.4Ghz, though, one of these days, with a Corona module/receiver. Have been running this Corona combo (same transmitter) on my 1/5 KP09 bike, along with 13.5T and XE60A (std software, so far) with the same batteries and no glitches at all...
Can you be more specific on what type of resistor and how to connect it?
I am going to revert to 2.4Ghz, though, one of these days, with a Corona module/receiver. Have been running this Corona combo (same transmitter) on my 1/5 KP09 bike, along with 13.5T and XE60A (std software, so far) with the same batteries and no glitches at all...
Can you be more specific on what type of resistor and how to connect it?
Which firmware are you using on the xerun120a? I have one installed on my 1/10 offroad buggy with a 5.5t sensorless and i was hoping you share the settings, firmware and fdr. Thanks
#611
thanks mate, ill try your settings this friday.
c2b, theres a memorial meeting at wlrc this bank holiday monday.if youve not raced here before your missing out big time, fancy coming down with a couple of the maritime boys???????????? lets give those tekin gm spxx boys a run for their money lol. there will be at least 7-10 from our local club night going down there, it will be a really good day, spread the word mate
c2b, theres a memorial meeting at wlrc this bank holiday monday.if youve not raced here before your missing out big time, fancy coming down with a couple of the maritime boys???????????? lets give those tekin gm spxx boys a run for their money lol. there will be at least 7-10 from our local club night going down there, it will be a really good day, spread the word mate
#612
Tech Addict
iTrader: (40)
Today I tried the software 324 in the race, race club as good as warm up the Italian league, class 17.5 with excellent results
TQ and victory in the final A.
Performance was on a par with other competing ESC, Tekin, LRP SXXSS, Mamba Max and engine temperatures always constant at 60/65C° with environment temerature 20/22C°.
I am very happy with this 324
You can see the track here:
http://www.laurenziana.it/modellismo/
TQ and victory in the final A.
Performance was on a par with other competing ESC, Tekin, LRP SXXSS, Mamba Max and engine temperatures always constant at 60/65C° with environment temerature 20/22C°.
I am very happy with this 324
You can see the track here:
http://www.laurenziana.it/modellismo/
#613
#614
Tech Rookie
#615
anyone got setting 324 for 11.5t? care to share??