Tamiya TRF415
Tech Regular
Originally Posted by BritRacer
do you know a part no. or have a link to them. All i can find is the alu ones and the kingpins, not the 5mm balls that so on the steering part of the upright.
Tech Master
iTrader: (6)
don't have enough clearance for servo turnbuckle
do i need slim/small servo for MSX? double check my assembly for error but there's simply not enough clearance under MSX upper deck to attach the servo turnbuckle. i've std size futaba 9000 series servo on MS; thought it would simply fit Haven't tried with sanwa vb/vr servos though. Any idea?
Tech Master
iTrader: (6)
Wouldn't that be more the servo horn's issue rather than the servo itself?
Originally Posted by Burlap
Wouldn't that be more the servo horn's issue rather than the servo itself?
but i belive you're right in that ODAWG315 prolly doesnt have the correct servo saver
Tech Master
iTrader: (6)
i'm using kit supplied servo horn and black tamiya servo saver
Tech Elite
iTrader: (74)
servo
futaba 9550 with tamiya blk servo saver
Tech Master
iTrader: (1)
Steering linkage issues!!!!!!
Originally Posted by KoE
do i need slim/small servo for MSX? double check my assembly for error but there's simply not enough clearance under MSX upper deck to attach the servo turnbuckle. i've std size futaba 9000 series servo on MS; thought it would simply fit Haven't tried with sanwa vb/vr servos though. Any idea?
Just my 2$
Tech Master
iTrader: (6)
When i disassembled my MS, i'd left servo/servo saver/servo turnbuckle as they were. The MSX steering linkage sits lower as it should be per instruction as compared to that on MS....right?
Ima recheck the servo saver (or perhaps change/remove) and snap some pics tonite
Ima recheck the servo saver (or perhaps change/remove) and snap some pics tonite
Tech Regular
Bumper for TRF415msx
Last Sunday I noticed that the factory bumper was of little use in a mod/6turn/carpet crash. I had a spare XXX-S on my pit table so I removed the BRP bumper. I was prepared to drill holes to get it to fit but it was a perfect fit! I did have to drill the extra hole that the BRP bumper uses but the body post holes are perfect for the 415.
Save the front end/ BPR Bumper
Save the front end/ BPR Bumper
Tech Master
iTrader: (45)
Originally Posted by Charles
Last Sunday I noticed that the factory bumper was of little use in a mod/6turn/carpet crash. I had a spare XXX-S on my pit table so I removed the BRP bumper. I was prepared to drill holes to get it to fit but it was a perfect fit! I did have to drill the extra hole that the BRP bumper uses but the body post holes are perfect for the 415.
Save the front end/ BPR Bumper
Save the front end/ BPR Bumper
And for the golden shafts?? anybody???
Tech Master
iTrader: (6)
Originally Posted by Charles
Last Sunday I noticed that the factory bumper was of little use in a mod/6turn/carpet crash. I had a spare XXX-S on my pit table so I removed the BRP bumper. I was prepared to drill holes to get it to fit but it was a perfect fit! I did have to drill the extra hole that the BRP bumper uses but the body post holes are perfect for the 415.
Save the front end/ BPR Bumper
Save the front end/ BPR Bumper
Tech Elite
iTrader: (10)
I've not had a problem with the std bumper. I have a few "square" ones cause they looked cool though.
maxoo - I also want to know. I think they are made by square, but I have no idea what part number they are. They could be an Alex Racing part too, but again, I'm not sure. If anyone knows, it'd be handy.
maxoo - I also want to know. I think they are made by square, but I have no idea what part number they are. They could be an Alex Racing part too, but again, I'm not sure. If anyone knows, it'd be handy.
Tech Champion
iTrader: (4)
Maxoo, F.Alonso - I'm pretty sure there Titanium Nitride coated shafts, same as the hingepins and shock shafts that you can get for the car.
However, I'm not sure there a proper Tam part, cause if you looks closely at the picture, you can see there is a spacer between the steering knuckle, and hex hub. Says to me that the axle is from something else... so maybe the whole of the dogbone/axle assembly has been retrofitted from another car...
F.Alonso is probably right that it's an alex racing bit though, I'm sure I remember reading somewhere that the shock shafts and hingepins are manufactured by them....
HiH
Ed
However, I'm not sure there a proper Tam part, cause if you looks closely at the picture, you can see there is a spacer between the steering knuckle, and hex hub. Says to me that the axle is from something else... so maybe the whole of the dogbone/axle assembly has been retrofitted from another car...
F.Alonso is probably right that it's an alex racing bit though, I'm sure I remember reading somewhere that the shock shafts and hingepins are manufactured by them....
HiH
Ed
Originally Posted by Burlap
Thank the Lord I hate the standard 415 bumper. Destroyed two of them so far.