Hpi Pro 4
Tech Elite
iTrader: (11)
mine has been on back order for 3 weeks, just grab the 2mm for now.
Originally Posted by josh69162
Does anyone have the Hara upper deck in stock? Nothing shows up on Tower...
-Josh
-Josh
Tech Addict
iTrader: (29)
JW- My steering rack rubs sometimes to. Just sand it slightly and also make sure to align the arm blocks since they were designed to move slightly. Usually just loosen the back one slightly and move it close to the front and tighten it back down. Then you shouldn't have any more rubbing.
Tech Champion
iTrader: (9)
Originally Posted by floodo1
pretty sure none of the hara parts are actually avail in the US. horizon, tower, stormer, etc...none have ANY of the new parts (shock bladders, upper deck, motor mount, etc)
most of the new '05 option parts are available overseas.
I purchased my new upperdeck, shocks, and motormount from RainbowTen in Japan... RcModel may have some of them now too...
Tech Lord
iTrader: (38)
I saw a Hara about a month ago..looked cool..
Tech Champion
iTrader: (9)
Originally Posted by xxxkat
I saw a Hara about a month ago..looked cool..
Tech Master
Thanks gentelman! I followed your advice, and the problem is cured!
Once again, I appreciate the help!!!!
Once again, I appreciate the help!!!!
What exactly is the difference between the Hara/'05 deck and the standard deck. The Hara/'05 is 0.25mm thicker, right?
-Josh
-Josh
Originally Posted by josh69162
What exactly is the difference between the Hara/'05 deck and the standard deck. The Hara/'05 is 0.25mm thicker, right?
-Josh
-Josh
The Hara deck is also thinner and has more cut out of the middle
Tech Regular
Hi Chad, thanx for the reply. I have an out the box pro4 with foams running on carpet, & its as good as anything out there. I am looking at purchasing a Hara pro4 to be set up for bitumen racing only. I run in stock & soon 19 turn classes.I was going to fit a 2mm chassis to this car to help with a little traction, either that or save some coin for a cyclone, but I like the pro4.
One last thing, fitting 3700's into a pro4, anyone successfully done this & if so what is the best way ?
Thanx guys
One last thing, fitting 3700's into a pro4, anyone successfully done this & if so what is the best way ?
Thanx guys
ok what is exactly the O-ring mod wherew does it go ?
Originally Posted by jim beam
One last thing, fitting 3700's into a pro4, anyone successfully done this & if so what is the best way ?
Thanx guys
Thanx guys
Originally Posted by ngo8
ok what is exactly the O-ring mod wherew does it go ?
Take a look at some pics of the 2005 Hara edition's steering rack upperdeck mounts and you'll get the idea.
Speaking of the o-ring mod, has anybody tried at Hara-spec upper deck on carpet?
I'm currently using a BMI 3mm main chassis and upperdeck on my carpet Pro4, but I usually have a tweak problem after a slight tap on the boards. Usually it not too bad and I can just drive around it (albiet more slowly!), but it is still annoying to have to re-set my car in the pits after every tap-o-the-boards.
I know the general idea behind the Hara spec upper deck is for lateral flex, but will this flex do more hurt than help on carpet?
I'm currently using a BMI 3mm main chassis and upperdeck on my carpet Pro4, but I usually have a tweak problem after a slight tap on the boards. Usually it not too bad and I can just drive around it (albiet more slowly!), but it is still annoying to have to re-set my car in the pits after every tap-o-the-boards.
I know the general idea behind the Hara spec upper deck is for lateral flex, but will this flex do more hurt than help on carpet?