|
Just wait for the front hex parts from the new RS to come out.
|
Originally Posted by Asharus
(Post 9237268)
I have the JC adapters and JC rulux 12mm wheels in the rear. I had no choice because the outdoor track I went to didn't have the SC10 wheels in stock on a race day for a set of goosebumps. At my other track (indoor clay) I use the SC10 wheels / barcodes.
Swapping out the adapter with the factory spacer is very easy and the adapter set is under 10 bucks. You'll still be able to use your factory wheels until you're done w/ the tires and eventually go full hex if you wanted to. |
I am looking at new bodies and was wondering if anyone had used the jconcepts truth v2 and noticed a difference over the stock bodie?
Thanks |
Just just finished going through and painting a used SC10 FT I picked up from a fellow racer. Cant wait to start racing SC along side my Stadium Truck.
Pic of the new body with the Tattered T4.1 FT in the back http://farm6.static.flickr.com/5143/...31de8795_b.jpg |
Originally Posted by euromut
(Post 9241930)
Just just finished going through and painting a used SC10 FT I picked up from a fellow racer. Cant wait to start racing SC along side my Stadium Truck.
Pic of the new body with the Tattered T4.1 FT in the back http://farm6.static.flickr.com/5143/...31de8795_b.jpg |
set up help
Need some set up help please. Racing on a hard pack surface with a fine loose dust. Trying to get the truck to hook up better under acceleration. We are using a spec tire ( hpi rtr tire and foam ).
Changes tried: red front springs green rear springs all squat taken out 4 degree toe block put in rear frt shocks stood all the way up. 35 wt frt with 3 piston 35 wt rear with 1 piston The changes made are better than the stock set up for the Fteam set up. But looking for more traction under accel. Thanks and God Bless |
Just picked up a FT today and was wondering any tips for assembly. I plan on doing a little racing and some driving around the neighborhood. I have been looking through ALL the 406 pages but that will take me a couple weeks. Anyway looking at sterring servos and wondering what you think is a good minimum. What else do I need to make this easier?
Thanks Mark |
Originally Posted by mark in wi
(Post 9242660)
Just picked up a FT today and was wondering any tips for assembly. I plan on doing a little racing and some driving around the neighborhood. I have been looking through ALL the 406 pages but that will take me a couple weeks. Anyway looking at sterring servos and wondering what you think is a good minimum. What else do I need to make this easier?
Thanks Mark |
Does anyone know if the RC8 shocks would fit the SC10 at all?
|
Originally Posted by Jsaves
(Post 9242573)
Need some set up help please. Racing on a hard pack surface with a fine loose dust. Trying to get the truck to hook up better under acceleration. We are using a spec tire ( hpi rtr tire and foam ).
Changes tried: red front springs green rear springs all squat taken out 4 degree toe block put in rear frt shocks stood all the way up. 35 wt frt with 3 piston 35 wt rear with 1 piston The changes made are better than the stock set up for the Fteam set up. But looking for more traction under accel. Thanks and God Bless |
need a 13.5 gearing(lightly boost)
|
Originally Posted by 20 SMOKE
(Post 9245403)
need a 13.5 gearing(lightly boost)
|
try 84/20 as a good starting point and temp your motor. I'm assuming running at the Asylum or Titusville?
|
put the factory 3.5deg rear toe back in the truck and get some toe in hubs to to stabilize the rear. put softer shock oil in the rear What hop up would you guys recommend for a FTeam SC10? |
Hi guys...simple question. How does the standard gearbox/diff setup go with modified motors? Do they hold up ok?
|
| All times are GMT -7. It is currently 08:47 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.