![]() |
Originally Posted by Pimpin
(Post 7345876)
It's all about the AKA wishbone. Dialed!!
|
Originally Posted by Pimpin
(Post 7345876)
It's all about the AKA wishbone. Dialed!!
I have some for my 8ight but the Barcodes were more dialed at OCRC and I also saw a set on a Hyper 10SC 4w and they had worn quickly. |
4 Attachment(s)
My latest mod with STC 1º rear hubs, JC relux :tire:, proline rears:nod:
|
Originally Posted by Pimpin
(Post 7345876)
It's all about the AKA wishbone. Dialed!!
|
hey guys i raced my sc10 today on hard packed clay it was very loose plz help me out here
|
Originally Posted by cyclone x
(Post 7349938)
hey guys i raced my sc10 today on hard packed clay it was very loose plz help me out here
|
Originally Posted by cyclone x
(Post 7355362)
can i get some help
|
Originally Posted by Matt Trimmings
(Post 7355683)
You should probably post your current setup.
|
Originally Posted by cyclone x
(Post 7355362)
can i get some help
Originally Posted by Matt Trimmings
(Post 7355683)
You should probably post your current setup.
Originally Posted by cyclone x
(Post 7355794)
well the person that is letting me use it still has the stock setup
What are the others running? Anyone at your track dialed with their truck? |
Originally Posted by F N CUDA
(Post 7356478)
Tires, correct ones for your track is the first step.
What are the others running? Anyone at your track dialed with their truck? Take some of the "punch' out of your motor if you can by programming your speed control. Most importantly....Dont keep posting the same question over and over you might piss someone off :D |
I am running a 16 / 87 with an EZ run ESC and a 4600kv mamba Max motor. I use a 4000mah 25c lipo. I went out today and did a 6 min run with a transponder so I was really pushing the truck and when I got back off the track after only 6-7 minutes I had a motor temp of 200 degrees. It has been running close or over 200 degrees since I put in the temporary EZ Run ESC. (my Mamba Max ESC is in for repairs).
I would like to gear it higher because I am coming up short on a few high speed jumps but I know it will be too hot. What is causing this? Also is there any way to keep my titanium turnbuckles from popping off the ball studs? I tried RMP ends but that didnt really help. |
Originally Posted by F N CUDA
(Post 7356478)
Tires, correct ones for your track is the first step.
What are the others running? Anyone at your track dialed with their truck? |
Calibers are horrible. Try something else.
|
Originally Posted by F N CUDA
(Post 7346844)
Front and rear on the 2w SC10?
I have some for my 8ight but the Barcodes were more dialed at OCRC and I also saw a set on a Hyper 10SC 4w and they had worn quickly. Wishbones work pretty much everywhere. Love em |
Originally Posted by will g
(Post 7346051)
has anyone tried to put the vcs2 shock caps and bladders on the shocks yet ... i cant seem to get my factory team shocks to feel right..i think its because im not rebuilding them right.... will these caps and bladders help with this or am i wasting my time thinking about them.. .thnx Will G
|
| All times are GMT -7. It is currently 09:08 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.