The Speed Passion Thread
Tech Regular
Been using reedy mach2 motors for a while and and have gotten bored with its power delivery. Thinking about getting a v4 7.5 for t5m truck. What's the power delivery like for the v4? Smooth, strong mid range? Anyone tried both reedy mach2/any copy and v4 that can tell me the difference? Does one motor feel livelier?
What does the r and s stand for on the reventon esc?
Do they come with Blinky loaded?
Do they come with Blinky loaded?
Last edited by RC GB; 05-18-2015 at 12:28 AM.
Tech Champion
iTrader: (42)
Then once you choose your profile, calibrate your ESC to the TX. If you have swapped the sensor wire and other things you mentioned maybe also look at the motors sensor board. Did you try running with no sensor wire attached? If it still runs strange with no sensor wire the sensor board in the motor might need to be replaced.
Been using reedy mach2 motors for a while and and have gotten bored with its power delivery. Thinking about getting a v4 7.5 for t5m truck. What's the power delivery like for the v4? Smooth, strong mid range? Anyone tried both reedy mach2/any copy and v4 that can tell me the difference? Does one motor feel livelier?
They just designate different levels of ESC. Racing and Sport is what some say, but not necessarily official designations.
Thanks Nexus ... will try ..
hi guys, not to sure if im ding this right, i have reventon pro 1.1. i finally got it in blinky mode, upgrade firmware,software everything i can, (I think) lol
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
Tech Addict
iTrader: (13)
hi guys, not to sure if im ding this right, i have reventon pro 1.1. i finally got it in blinky mode, upgrade firmware,software everything i can, (I think) lol
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
If your track only will allow it if it single blinks, then there are a lot of speed controls that can not be run. For instance, I've had esc's that didn't have any options to change the timing and they didn't flash at all.
If you find a solution to this, please post it here. However, I think this is how the programming is designed.
sincerley,
tim
Mine does the same thing and I went through the same research. I never got an answer. From what I could find, the ESC is using the single blink to mean low voltage (or something like that). Therefore, they use the double blink for 0 timing. I have never had a problem with tech inspections with this.
If your track only will allow it if it single blinks, then there are a lot of speed controls that can not be run. For instance, I've had esc's that didn't have any options to change the timing and they didn't flash at all.
If you find a solution to this, please post it here. However, I think this is how the programming is designed.
sincerley,
tim
If your track only will allow it if it single blinks, then there are a lot of speed controls that can not be run. For instance, I've had esc's that didn't have any options to change the timing and they didn't flash at all.
If you find a solution to this, please post it here. However, I think this is how the programming is designed.
sincerley,
tim
if I ever hear back from Speedpassion I will post it for sure.
reventon pro 1.1 can put latest software Fleta V 1.4?
Tech Champion
iTrader: (42)
hi guys, not to sure if im ding this right, i have reventon pro 1.1. i finally got it in blinky mode, upgrade firmware,software everything i can, (I think) lol
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
Being that it is a Much More Racing firmware there's no way to tell without testing. If you brick it though, I don't believe the Speed Passion safe mode will be able to save you. For sure it's not supported or recommended by Speed Passion.
Tech Regular
iTrader: (25)
hi guys, not to sure if im ding this right, i have reventon pro 1.1. i finally got it in blinky mode, upgrade firmware,software everything i can, (I think) lol
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
no volt protection = done
software stock0 V21
lcd program card software V2.7
so looking at all the videos out there of blinky mode, mine blinks twice then pauses and twice, and on on on................anyways i can race in my calss because of it. does anyone knoe how to fix this cause its been a a week of emails with speed passion and ive gotton no where the moter is speed passion 3.0. all this stuff is brand new.
thx raz
Tech Rookie
Hi, guys sorry if the question sounds dumb, but i'm new to this,
Will the Speed Passion GT 2.0 pro carbon work with a Xerun 10.5 sensored motor?
Thanks in advance.
Will the Speed Passion GT 2.0 pro carbon work with a Xerun 10.5 sensored motor?
Thanks in advance.
is it safe if i disable thermal protection esc to run 4,5T motor ? esc reventon pro 1.1
Tech Champion
iTrader: (42)
A 10.5T is fine to run with the GT 2.0 Pros.
I never run thermal or voltage protection. That being said I probably wouldn't run a 4.5 for 15 minutes straight on a hot day at the track
I have a revention stock club racer and cannot get any brakes. Using m8 radio.
tried searching but didnt have much luck. can anyone tell me how to get more brakes on my reventon pro 1.1? ive put reverse power to 100 and brakes to 100 and its still very weak.