Chris08527

iTrader: (16)

anyone running the T3 or the 11 in the stock class??? how is it getting close to that low FDR???

Corally_27

hi

yesterday i finished to build my new 2011 i have to say that the kit is awesome except for the shocks, i found one shock shaft with no groves for the c clips and two shock cap nut to small to fit in the the part which goes in it. now i have to wait for my lhs to open

P.I.M.P

iTrader: (14)

Hey me to same problem cap to small to fit the plastic shock mount and parts wrong colour...and one other guy as well no clips to mount the piston.what is going on with xray ever since the second run of 09 kits I have had stuff wrong and I'm not the only one I order 3 09 kits ones and all had some issue of some sort out. of three t3'10 kits two where fine 1 had problem and now stuff still going wrong with t3'11.not liking xray At the moment:-(

Xchange

iTrader: (10)

I try yesterday the ecs drive shaft and i do not see any difference in lap time.

Next thing to try is a gear diff in the rear but i ran tam shock again yesterday and i was very impressed to feel how car rotate smooth in comparaison with the xray shocks

Any way, may be it s me i dont know how to build xray shock hehe

hanulec

iTrader: (28)

Hey Chris - you need some 92 or 90 tooth (or even smaller but probably not smaller than 88t) spurs to run the non-boosted stock class. XRay makes as low as a 92t. RW had spurs designed for XRay in a orange header card that were thinned to fit on the lay shaft. If you cannot find either type then just stock up on "cheap" small spurs and get yourself a dremel with a flat head grinding stone to take material away from the spur so that it fits. I've done this a bunch of time already for racers at IIC and Horsham. I've been using this tip: http://www.dremel.com/en-us/Attachme....aspx?pid=8193

It looks like Nexus has a bunch of the small spurs that fit in stock:

XRay 92t - http://www.nexusracing.com/index.php?cPath=145_321_436
RW gears all the way to 72t - http://www.nexusracing.com/index.php?cPath=145_321_322

Chris08527

iTrader: (16)

thanks hanulec, your like a walking RC-pedia and if nexus doenst have it, could always check www.hanulecsbigyellowpitbox.com . . .LOL

Drew Ellis

Guys sorry to hear that. You can call RCAmerica and send the parts in and we will replace them. I know that takes time for you guys to get the parts back and I apologize for the inconvenience and we will make note to say something to Xray.

Thanks Drew
214-744-2400
[email protected]

bfong13

iTrader: (18)

Just finished with the build. Everything went together well, however, I think the kit was missing a few screws. No problem as I had a surplus of parts from other cars. Only complaint I have is that Xray didn't include any turnbuckle wrenches (3mm and 4mm). They didn't have to include the fancy Hudy ones, but if they could've included some cheap turnbuckle wrenches to help with the build, that would've been good.

[IMG][/IMG]

RCknight

iTrader: (5)

Quick can someone tell me what pinion gear I need for 5.0 gear ratio with 100t spur. thanks

rx7ttlm

iTrader: (30)

I think once I get a gear diff in my hands and I check out a couple different shock orings, the t3 will have no complaints from me. I was super quick last season with the T3 once I got it sorted. Looking forward to hitting the rug this season with the new car

Danny-b23

iTrader: (3)

38 tooth.

Korgae

iTrader: (15)

What track in Quebec do you ran at?

mok

iTrader: (9)

what servos use the narrower servo post holes?

cant seem to find any suitable servo with dimensions less than 40.5mm wide (which uses the wide holes)

-Mark

Yokomo_Ant3

iTrader: (29)

I ran my car for the first time yesterday, the car has a lot more rear grip than the T3 and the steering is much smoother. I was having issues with driveshafts for some reason yesterday I ran it 3 races, all 3 my rear driveshaft pins came out, and in the 1st race the whole rear driveshaft fell out Yes they were loctite'd. Then in the 3rd race i completely sheared a front driveshaft, just from driving. Oh well, time for some flat spot pins and stronger loctite. never had that issue on my T3.

I definatly need more time with this car as it wasnt driving perfectly yesterday. It needs more overally steering, and definatly needs more high speed steering. Anyone have any suggestions?

Here is the setup sheet
http://forum.teamxray.com/xform/inde...&setup=t3_2011

Here is what i was thinking of changing. Thoughts?
http://forum.teamxray.com/xform/inde...&setup=t3_2011

Thanks,

Antoni

shanty140

iTrader: (5)

Anyone know an Online shop that has these in stock?