4LikesNEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
01-11-2011, 08:01 AM
#2251
Hi guys
there was a mistake on the previous instructions for the 2 tyoes of firmware i have attached the correct ones .
sorry about that and yes also we will have the 508 v3.0 with the 8 options of brskes but the led card will not be able to be used just the lcd programmer.
there was a mistake on the previous instructions for the 2 tyoes of firmware i have attached the correct ones .
sorry about that and yes also we will have the 508 v3.0 with the 8 options of brskes but the led card will not be able to be used just the lcd programmer.
01-11-2011, 08:02 AM
#2252
Tech Adept
weird because 1224 worked great with my Duo3 in Touring Car and was nice and cold but quick
01-11-2011, 10:51 AM
#2254
Tech Adept
and actually, everyone else's conundrum as well ...
looking forward to the next time I will be down at the track for further runs with the speedo
there was just not enough time the last time round ...
01-11-2011, 10:52 AM
#2255
01-11-2011, 10:58 AM
#2256
Tech Regular
Just put the "old" turbo degrees extra by boost and make the rpm range fit perfect for the track...That is what i`m going to do outside.
(and offcourse a late turbo 0,5s, that only works on the straight, ala Hara.....for the mach outdoors, on really high rpm the motor cann handle more timing..)
It starts with stifness, from there displacement is calculated and stresses,
will see how it ends.....lol
01-11-2011, 11:04 AM
#2257
Tech Adept
btw the document is all in english, but i suspect characters like ( ) / are not in english ... i think ... found that out when I was resizing the fonts in the earlier document and found out that they were just characters and not recognised by word ... a bit of re-typing and managed to sort out the document just so that the large table in between do not appear in between pages, when the document is printed out, sorry am a bit of a OCD
01-11-2011, 11:06 AM
#2258
Tech Adept
could be a silly question, but doesnt the amount of adjustability in 1224 make 110108 a little redundant? or are the changes a little more sinister and for a reason? As surely you could just set 1224 to limit at 30 degrees by working out the actual total?
Btw the document does confirm some points to how this differs to the old 518.
Aka More timing/boost and a controllable turbo curve
Btw the document does confirm some points to how this differs to the old 518.
Aka More timing/boost and a controllable turbo curve
01-11-2011, 11:11 AM
#2259
just install the chinese fonts and it will work fine ...
btw the document is all in english, but i suspect characters like ( ) / are not in english ... i think ... found that out when I was resizing the fonts in the earlier document and found out that they were just characters and not recognised by word ... a bit of re-typing and managed to sort out the document just so that the large table in between do not appear in between pages, when the document is printed out, sorry am a bit of a OCD
btw the document is all in english, but i suspect characters like ( ) / are not in english ... i think ... found that out when I was resizing the fonts in the earlier document and found out that they were just characters and not recognised by word ... a bit of re-typing and managed to sort out the document just so that the large table in between do not appear in between pages, when the document is printed out, sorry am a bit of a OCD
01-11-2011, 11:21 AM
#2260
XERUN-120A-1S-SD (V2.1) Brushless ESC
software/firmware, which one for Stock and were do I download it?
post a starting setup for the above please using 10.5 in 12th pancar
7.5 if you have one also
running on a medium sized & grip carpet track
have the software and hand held LCD programmer at the ready
software/firmware, which one for Stock and were do I download it?
post a starting setup for the above please using 10.5 in 12th pancar
7.5 if you have one also
running on a medium sized & grip carpet track
have the software and hand held LCD programmer at the ready
01-11-2011, 01:19 PM
#2261
I'm so confused 
I Have two questions:
1)What motors should uses 1224 ?
2) On 110108 ,on the table with the recommended settings for 1/10 on-road
with 11.5T motor #13 boost start RPM is set to 2000.On 1224 for 11.5T motor #13 boost start RPM is set to 7000.
2000RPM on #13 for a 11.5T is correct?
I Have two questions:
1)What motors should uses 1224 ?
2) On 110108 ,on the table with the recommended settings for 1/10 on-road
with 11.5T motor #13 boost start RPM is set to 2000.On 1224 for 11.5T motor #13 boost start RPM is set to 7000.
2000RPM on #13 for a 11.5T is correct?
01-11-2011, 04:00 PM
#2262
Hi, can i use soft 110108_STOCK for my sensorless 13T motor?
I am afraid if this soft only for sensored motor.
Thank you.
I am afraid if this soft only for sensored motor.
Thank you.
01-11-2011, 05:11 PM
#2263
Dear Loyal Customers
I have an annoucement to make for the USA market within 48 hours
I will answer all your pm's soon and all your thread questions very soon.
sorry for the delay
regards Angelo
I have an annoucement to make for the USA market within 48 hours
I will answer all your pm's soon and all your thread questions very soon.
sorry for the delay
regards Angelo
01-11-2011, 06:02 PM
#2264
01-11-2011, 06:11 PM
#2265
Hi guys
I have set up download links on the following website for you guys to download the files much easier
http://www.cobrarc.com.au/
regards Angelo
I have set up download links on the following website for you guys to download the files much easier
http://www.cobrarc.com.au/
regards Angelo