TLR 22 3.0 Race Kit Thread!
|
|||
#2461
Frank just wondering what the benefits of the +3 rear hubs are and if they increase/reduce the amount of driveshaft in the outdrive?
#2462
Tech Initiate
Laydown trans conversion coming too! http://www.redrc.net/2016/03/tlr-22-...on-conversion/
#2463
#2464
Tech Regular
iTrader: (63)
They should release a full kit as well (my opinion). Just a matter of putting it all in a box with a manual. I know I'm going to end up building a 2nd car after all is said and done.
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
#2465
They should release a full kit as well (my opinion). Just a matter of putting it all in a box with a manual. I know I'm going to end up building a 2nd car after all is said and done.
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
#2466
Tech Master
iTrader: (67)
They should release a full kit as well (my opinion). Just a matter of putting it all in a box with a manual. I know I'm going to end up building a 2nd car after all is said and done.
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
Maybe with stiffer springs and HRC blocks included? I don't know if anybody's running the HRC pivots, but I've got some on the way to try out. (carpet)
#2467
I agree... Even though I already have the 3.0 and my local track is carpet, I would absolutely buy a carpet-specific kit if it came out and then leave this one set up for dirt. Hopefully Frank and the team take this into consideration and maybe offer both the conversion and a complete kit. One can hope!
#2470
Originally developed for the 22-4, we found these hubs to increase performance for the 22 3.0 on higher grip carpet and Astro tracks.
Aluminum chassis, machined gear cases, motor plate, carbon battery strap, body, aluminum rear hubs, and all the hardware. I think you'll find it is by far the best "lay down" value.
#2471
Tech Rookie
HELP !!!
My first build . As soon as I mount the Camber Tierod's the suspension arms bind. They're not free like the rears. What am I doing wrong? I triple checked the length and I'm right on 77.4 mm per spec.What am I doing wrong ?!!!!!!
My first build . As soon as I mount the Camber Tierod's the suspension arms bind. They're not free like the rears. What am I doing wrong? I triple checked the length and I'm right on 77.4 mm per spec.What am I doing wrong ?!!!!!!
#2472
Tech Initiate
#2473
Put a battery in it and run it. They will move freely by the time you get back to your pit table.
#2475
Without posting my full setup, although I can do that later, my inside rear tire is lifting during hard corners. This is on a high-grip carpet track. What is going on with the car? Too much weight transfer to the front outside? What types of things would I do to address this?
My first thought is stiffer front springs. Then I'm just guessing at thicker rear oil, maybe less droop in the rear.
Thanks!
My first thought is stiffer front springs. Then I'm just guessing at thicker rear oil, maybe less droop in the rear.
Thanks!