R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
 
Search: Posts Made By: asalk
Showing results 1 to 25 of 28
Search took 0.01 seconds.
04-30-2015, 01:05 AM
Replies: 2,107
Views: 684,984
Posted By asalk

Could someone recommend starting setup for very...

Could someone recommend starting setup for very low grip and bumpy track?
Thanks in advance.
02-23-2015, 09:20 AM
Replies: 4,165
Views: 739,928
Posted By asalk

To what gear ratio this translates with 56mm...

To what gear ratio this translates with 56mm wheels?
02-22-2015, 10:23 AM
Replies: 4,165
Views: 739,928
Posted By asalk

Gearing for 13.5 blinky 1S?

Could someone recommend gearing for 13.5 blinky 1S?
I will use it in X-10 SE with Trinity Epic D3.5 on 30m x 15m carpet.

Thanks.
12-12-2014, 05:17 AM
Replies: 83
Views: 24,547
Posted By asalk

ultimate 2014 manual

Anybody has user manual for the new Sakura 2014 and can share it?
06-04-2013, 11:40 AM
Replies: 2,291
Views: 634,197
Posted By asalk

Pre orders started at rcmart.com, for 129USD.

Pre orders started at rcmart.com, for 129USD.
05-14-2013, 06:48 AM
Replies: 21
Views: 4,291
Posted By asalk

Sakura Xi Sport is on its way, i would wait for...

Sakura Xi Sport is on its way, i would wait for it...
04-02-2013, 10:57 PM
Replies: 13,431
Views: 1,994,451
Posted By asalk

Have two reventons pro in 1:10 buggy and TC for...

Have two reventons pro in 1:10 buggy and TC for more than half a year, no problems at all.
10-29-2012, 04:07 AM
Replies: 5
Views: 756
Posted By asalk

PM sent.

PM sent.
10-09-2012, 03:49 AM
Replies: 2,428
Views: 759,423
Posted By asalk

No one is forcing you to buy this radio, you can...

No one is forcing you to buy this radio, you can choose cheaper alternative...
10-05-2012, 02:28 AM
Replies: 46,539
Views: 5,932,634
Posted By asalk

Level 1 with 5200kv tenshock.

Level 1 with 5200kv tenshock.
09-03-2012, 05:14 AM
Replies: 1,505
Views: 251,255
Posted By asalk

It might be ESC temp cutoff, try disabling it.

It might be ESC temp cutoff, try disabling it.
08-28-2012, 11:06 PM
Replies: 1,505
Views: 251,255
Posted By asalk

I'm gearing it 40/14 on a large 1:8 outdoor track.

I'm gearing it 40/14 on a large 1:8 outdoor track.
08-21-2012, 05:20 AM
Replies: 46,539
Views: 5,932,634
Posted By asalk

Using ALIGN DS620 with no problems. Enough speed...

Using ALIGN DS620 with no problems. Enough speed and torque.
08-13-2012, 05:26 AM
Replies: 46,539
Views: 5,932,634
Posted By asalk

Tenshock SC411 is good alternative to Tekin Pro4.

Tenshock SC411 is good alternative to Tekin Pro4.
05-15-2012, 03:16 AM
Replies: 46,539
Views: 5,932,634
Posted By asalk

48tooth with .8 pitch may fit. Teeth on .8 are...

48tooth with .8 pitch may fit. Teeth on .8 are smaller than mod1, if you compare 40tooth .8 pitch with 40tooth mod1, you'll notice that .8 spur gear will be smaller in diameter.
04-26-2012, 03:20 AM
Replies: 2,113
Views: 522,532
Posted By asalk

I'm using it. savox 1251MG MT-4 RS Pro ...

I'm using it.

savox 1251MG
MT-4
RS Pro
Duo 3

no issues in 8months of usage.
03-27-2012, 02:55 AM
Replies: 3
Views: 795
Posted By asalk

They are ok. I used it a couple of months in my...

They are ok. I used it a couple of months in my xray t3. After a big crash middle part is broken. Unfortunately there are no spares available.
02-02-2012, 07:00 AM
Replies: 11
Views: 823
Posted By asalk

PM sent.

PM sent.
01-17-2012, 03:38 AM
Replies: 220
Views: 25,365
Posted By asalk

X-RAY T3'12

X-RAY T3'12, 17.5T, Lithuania
11-20-2011, 10:01 PM
Replies: 12,554
Views: 1,876,818
Posted By asalk

I tried with brand new sensor cable. Motor was...

I tried with brand new sensor cable. Motor was never above 60C. Over heat protection is disabled.

Is it possible that i burned something in esc when i soldered wires?
11-20-2011, 07:15 AM
Replies: 12,554
Views: 1,876,818
Posted By asalk

Blinking green

Hello,

I have a problem with my HW 120 v2.1.
I'm using it with Speed Passion comp v3 17.5motor and 930 firmware.
It was running perfect till i resoldered all the wires. Now when i apply throtle...
11-18-2011, 05:19 AM
Replies: 3
Views: 2,738
Posted By asalk

Same question for 17.5t

Same question for D3 17.5t, boosted + turbo. Thinking of 5.7fdr.
11-14-2011, 12:08 PM
Replies: 5
Views: 504
Posted By asalk

11-05-2011, 01:00 PM
Replies: 4,239
Views: 699,535
Posted By asalk

With the 84t spur i could fit only 30t pinion,...

With the 84t spur i could fit only 30t pinion, 31t won't fit.
06-26-2011, 09:14 AM
Replies: 7
Views: 1,123
Posted By asalk

6.5 is way too low. We have a class in local club...

6.5 is way too low. We have a class in local club where we race 15t brushed motors (HPI Firebolt 15t to be exact) with TC cars and with 6.5 FDR the temps on motors are above 212F (100C), which is...
Showing results 1 to 25 of 28
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.