R/C Tech Forums - Futaba 4PX

Page 53 of 160

« First

103

153

Last »

Show 40 post(s) from this thread on one page

R/C Tech Forums (https://www.rctech.net/forum/)

- Radio and Electronics (https://www.rctech.net/forum/radio-electronics-137/)

- - Futaba 4PX (https://www.rctech.net/forum/radio-electronics/809530-futaba-4px.html)

danny250r

11-24-2014 04:19 AM

Quote:

Originally Posted by Boz (Post 13677256)

Put your servo horn on.

Use the sub trim to put the horn at a 90deg angle (if that is what your instructions recommends).

Adjust the steering turn buckle (the one coming off of the servo) to centralize the steering rack.

Set the steering rods and camber links to equal lengths. It's not import if the toe-out is not spot on at this stage, it will be re-checked again later.

Adjust your steering end points to maximum throw. They should read the same figure each way or with in one or two.

Set you toe-out and camber and then re-check your maximum throw again.

Use the D/R to reduce your steering throw during a race, not the steering end points.

yea ive done all of that i always do when i set up a new servo or radio something is up with this radio im thinking even with right side end point all the way up still not even close to the amount on left side thx

Boz	11-24-2014 04:31 AM

what servo are you using?

Boz	11-24-2014 04:42 AM

Quote:

Originally Posted by RumbleBeeAL (Post 13677355)

Who's offering the best deals/discounts on the 4PX this week?

Please Post or PM any Black Friday / Special discount codes that you are aware of.

Thanks!

I think Danny250r may have one going cheap if he can't solve the problem.

danny250r

11-24-2014 05:03 AM

Quote:

Originally Posted by Boz (Post 13677387)

what servo are you using?

Savox 1252

danny250r

11-24-2014 05:04 AM

Quote:

Originally Posted by Boz (Post 13677398)

I think Danny250r may have one going cheap if he can't solve the problem.

Lmao you ain't kidding. Hahaha

dgrobe2112

11-24-2014 07:40 AM

something else to consider Danny.. go to a different model in the radio.. like.. model 10 or something..

kyle3333

11-24-2014 07:59 AM

Quote:

Originally Posted by trx450racer174 (Post 13673410)

New Firmware update guys FYI

http://www.futaba-rc.com/software-updates.html

Does the 4PX Software Update Ver. 1.1 fix the massive glitching/interference issues when using the 614fs receivers?

Toiffel

11-24-2014 08:41 AM

Quote:

Originally Posted by DekelzMan (Post 13675271)

Where'd you pick it up? I can't find an online retailer.

Straight from Hiro_Seiko, send them an email with the part numbers of what you are looking for, they will check stock and send back paypal info, takes about a week and a half to receive items, make sure you get the wheel adaptor if purchasing a wheel....

DekelzMan

11-24-2014 08:44 AM

Quote:

Originally Posted by Toiffel (Post 13677838)

Thanks Man, THAT was the answer I was looking for :)

TonyWest

11-24-2014 08:55 AM

I spoke to Futaba this morning and they would not give a statement either way.

JayL	11-24-2014 09:49 AM

Quote:

Originally Posted by kyle3333 (Post 13677762)

Does the 4PX Software Update Ver. 1.1 fix the massive glitching/interference issues when using the 614fs receivers?

I have had no issues with my 614fs-e

???

TonyWest

11-24-2014 12:34 PM

I had an issue with my 614 FF
A total stranger with a brand new 4PX had the same issue yesterday.
I have a total of two 4px's now because I thought it might be the radio.
I have done the firmware upgrades on both now.

I will be posting a 4px for sale that has been used once for $425 in the for sale section.

Odin544

11-24-2014 12:42 PM

No issues with either the rx that came with the radio or the 614fs from the 4pksr so far for me.

RumbleBeeAL

11-24-2014 01:36 PM

Quote:

Originally Posted by danny250r (Post 13677422)

Lmao you ain't kidding. Hahaha

rofl