![]() |
1) make the bec adjustable in increments rather than just 6v or 7.4
2) consider battery posts on another side and making the posts slightly bigger for 10 gauge wire 3) consider pre-wiring |
Got a question on my new rc8 gen 2. Was looking at the set up sheets and a lot of guys run 80 current limiter how many LEDs are lit up to get 80. Or is exact percentages only achieved through Hotwire.
Thanks |
Originally Posted by Waflet
(Post 12470330)
Hideeho
I have a couple of suggestions for some things to add to the datalog in the future. 1. The ability to copy & superimpose one section over another. 2. The ability to superimpose (& synchronize) one run over another. 1&2 This is being worked on already. now for the stretch goals 3. Have the datalog talk to the mylaps & mark laps on the log. 4. Have the datalog talk to the steering servo & log its possition. 3. This is unlikely as it would require an external module and working with Mylaps 4. Again this would likely require another module to grab the input of the servo and record it. I figure the 1st 2 aren't THAT difficult, because they should be back end stuff in the hot wire, not in the ESC. The last 2 would probably be more for the gen3, I assume. What I am wanting to do is be able to compare one lap or run directly with another. This would help greatly in finding which line is faster through a given corner with out have to rely on hitting every corner exactly the same every time. You could even compare multiple lines through multiple corners on the same lap. |
Originally Posted by fantomdude
(Post 12471018)
Got a question on my new rc8 gen 2. Was looking at the set up sheets and a lot of guys run 80 current limiter how many LEDs are lit up to get 80. Or is exact percentages only achieved through Hotwire.
Thanks http://www.teamtekin.com/hotwire_RX8.html |
Originally Posted by Randy_Pike
(Post 12471152)
Answers in red.
It is great to hear 1 & 2 being worked on! I didn't figure 3 or 4 would be possible:rolleyes:. |
Don't know if I'm late or not, but did anyone see this!? Gen 2 Case in black
http://www.amainhobbies.com/product_...en2-Case-Black |
Originally Posted by JRapid
(Post 12471195)
Don't know if I'm late or not, but did anyone see this!? Gen 2 Case in black
http://www.amainhobbies.com/product_...en2-Case-Black http://www.amainhobbies.com/product_...RX8-Gen2-Fan-2 |
Originally Posted by Mullet1
(Post 12471283)
|
im looking for a tablet thats inexpensive that can use to carry around in my hauler bag to use hotwire on my tekin esc . im sick of carrying around my laptop does anyone know of one that capable of that i have a new ipad but it has no usb ports so i need another
|
Originally Posted by Brandonmorris44
(Post 12471677)
im looking for a tablet thats inexpensive that can use to carry around in my hauler bag to use hotwire on my tekin esc . im sick of carrying around my laptop does anyone know of one that capable of that i have a new ipad but it has no usb ports so i need another
|
Originally Posted by Krio
(Post 12471912)
Nexus 7 should be able to, but don't quote me on it yet.
|
Originally Posted by Brandonmorris44
(Post 12472456)
Ok thanks I may check that one out
|
Originally Posted by Mullet1
(Post 12472476)
10 inch netbook, it's what I use. I bet you could find a old one on Ebay for less than $100
|
Originally Posted by Brandonmorris44
(Post 12472524)
It works good with Hotwire ?
|
can anyone tell me if the rx8 gen2 has the active braking like the rs.
thanks |
| All times are GMT -7. It is currently 03:59 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.