I just wanted to drop a kudos to Speed Passion. After running Castle, LRP, Tekin, Orion, and now Speed Passion, I have to say that my Reventon Pro/Competition V3 is the best setup I've used. Smooth, fast, and reliable.

Great job guys!

I did that for a few runs with a 550 but it got way hot even with a fan, so I didnt do that anymore.

I'm pretty sure the prostock is like the old LPF but with a lower profile heat sink. So a 5.5 limit and NOT adequate for a 4x4 SCT. GT Pro is the bad ass one you want. :nod:

They are a great speed control but I think they are limited to 7.5/85 when running timing/boost. So I think if you were using something of a slower it might work but I'm not sure it would be competitive. I run 17.5 blinky in an sc10 2wd and it comes off cool with no fan. I bet when you start pulling the amps of low turn motor it will get warm pretty quick.

I thought that the 323 software was the best for mod. Did I miss the 428 as the newest/better option? :confused: This might be another option for you as I thought it was supposed to be better than the 205mod.

Mark

cool. thanks for the heads up. Pretty much run all GT2.0 Pros other than the pro stock I got in cheap. works well in the 2wd buggy so will keep it there lol

428 from what I can tell seemed very similar to 323, with a bit better temps. Pretty much used the stock stuff for awhile in 4x4 SCT, just configured as needed.

Run all mod software now in applicable vehicles since the timing settings in stock I wasn't using are by default greyed out in the mod software.

Main benefit I found was the turbo timing at WOT. using 5 degrees of it really work my Pro4 motor up and I could gear down and still get the top end I need. Temps dropped too.

When using the wifi module I see that you can change the firmware (ie: from no-timing, to mod..etc), but I only have one option which is mod- how to I get to the rest of the firmware options to switch to them?

Is there a link to instructions and software to update the lcd boxes for the reventon pro's

Cain after a little digging I found It might help you in the future if you need to swap an esc from the buggy to a truck. That was back on page 48 if you want to see any more. I know....its a slow day at work so I looked for it for a while. :lol:

Thanks for the info. Yeah, I was more curious than anything else. In general when 2.0 Pros come up for sale, I pick them up as the ESC is that good. Wouldn't mind the Reventon Pro but not being able to run 4 pole motors is a no-no for me.

I am hopeful that when they make the 1/8 scale version, they really consider letting the ESC be ran on 2S. This is pretty much what all the other companies are doing now, and take nothing away from the Reventon Pro in other usage than 1/10 4x4 SCT, which is really just a glorified 1/8 buggy in a lot of cases.

i wouldn't say "glorified" :lol:

Ahhh... I never would have thought to go at it from the other side. I might just give this a try.

Thanks!

This is a smart man! :)

J.P. Richards runs with the big dogs at the CRCRC Midwest Champs!
http://teamspeedpassion.com/wp-conte...rcrcdustin.jpg
http://teamspeedpassion.com/2013/01/...championships/


If you register with Team Speed Passion they said they will be emailing registered members early info on product releases and ESC setup sheets from team drivers.

Yes. I was at that race. He is a great guy and his brothers. They all tried to help me with my problem of changing the firmware but couldn't get it either.

What are the motor limits of this reventon esc?

http://www.speedpassion.net/shop/det...SP000060&c=ESC

9.5T or slower

http://www.speedpassion.net/reventon/home.asp

click compare to see the specs for all of them