|
Originally Posted by nate79
(Post 13235518)
i dont run boost or timing usually blinky mode mainly
|
ok thanks was running yesterday and my esc just went dead and wont come back on so ill be sending it in this week
|
1 Attachment(s)
Originally Posted by nikos2002
(Post 13234966)
If you search Viper R/C on YouTue. There is a video that walks you through how to use the VLink- sorry not on my laptop so I can't post the link.
You do need to make sure that you have downloaded the version for your version if VTX- each unit had a slightly different protocol - but all delivers the same performance in the end. When you plug your VTX into the VLink if an older software is on the unit it will automatically start to update. If you already have a64 on your unit and want to reset all the parameters. You have to initiate the download yourself. http://www.youtube.com/watch?v=GWGG_QR9TrY I have downloaded the correct file (ViperVLink_VTX10_10R_A64_For Black Edition Only_Release) and I followed the steps as described. On my vlink screen there is no indication of the firmware version of my esc, as seen on the video. Check out the attached screenshot from the youtube video, the area I marked with a green circle. I don't see anything like that on my vlink screen either before, or after the update. |
Originally Posted by nate79
(Post 13235607)
ok thanks was running yesterday and my esc just went dead and wont come back on so ill be sending it in this week
|
1 Attachment(s)
Originally Posted by billtc3
(Post 13235790)
I found this video on youtube:
http://www.youtube.com/watch?v=GWGG_QR9TrY I have downloaded the correct file (ViperVLink_VTX10_10R_A64_For Black Edition Only_Release) and I followed the steps as described. On my vlink screen there is no indication of the firmware version of my esc, as seen on the video. Check out the attached screenshot from the youtube video, the area I marked with a green circle. I don't see anything like that on my vlink screen either before, or after the update. |
Please read:
"...Check out the attached screenshot from the youtube video,..." The attached screenshot is from the youtube video, like I said, not from my vlink.... :rolleyes: Nikos, if it makes any sense to you, please let me know |
Originally Posted by billtc3
(Post 13236095)
Please read:
"...Check out the attached screenshot from the youtube video,..." The attached screenshot is from the youtube video, like I said, not from my vlink.... :rolleyes: Nikos, if it makes any sense to you, please let me know |
Originally Posted by billtc3
(Post 13236095)
Please read:
"...Check out the attached screenshot from the youtube video,..." The attached screenshot is from the youtube video, like I said, not from my vlink.... :rolleyes: Nikos, if it makes any sense to you, please let me know 1- plug battery into the esc 2- power the esc on 3- once it boots, press the vink button for about 2 seconds. 4- plug in the vlink cable and the usb PC link 5- run the viper software. |
Well feel like a idiot. Started trouble shooting my esc and hooked up my progauge to it and seen I had my lipo cut off set way to high. Lowered it down to where it should be and it works perfect again lol.
|
Yeah, but your "fix" was free! Dialed....
|
Hi guys what's the feedback on the vf8 motors? I have heard of case issues but not finding anything on this thread, are everyones motors holding up?
|
Well my ESC is going back to mother. It is acting real screwy. Work normal, but after 10 to 15 minutes acts like it hits LVC. It shakes, stutters, then stops. I unplug the battery, count to 30, plug the battery in and I run for another 10 to 15 minutes and it does the same thing all over again.
I dropped the LVC down to 5 volts. Did not make any difference. After the other issue of not turning off, and being locked out of forward. I think it needs to be looked at. I should have it in the mail by Tuesday. Buzz. |
@Wildcat1971
Who are you? Are you a Viper representative? If not, please stop replying to my posts. I would rather have somebody from Viper reply, one who can read English, who can write English and who knows what one is talking about. |
Originally Posted by billtc3
(Post 13237536)
@Wildcat1971
Who are you? Are you a Viper representative? If not, please stop replying to my posts. I would rather have somebody from Viper reply, one who can read English, who can write English and who knows what one is talking about. |
Originally Posted by billtc3
(Post 13237536)
@Wildcat1971
Who are you? Are you a Viper representative? If not, please stop replying to my posts. I would rather have somebody from Viper reply, one who can read English, who can write English and who knows what one is talking about. |
| All times are GMT -7. It is currently 11:49 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.