|
Originally Posted by COBRARACING
(Post 9646684)
Turbo delay Off means the turbo is not off but Just means the turbo will come on straight away once full throttle is achieved so there will not be any delay before it cuts in .Once the start rpm is met ,turbo slope starts to ramp up the turbo is always on just there is no delay for it to come on especially on long back straights were delay is essential .
|
Does the xtreme stock controller come with any wires or capacitors?
|
Originally Posted by YZFAndy
(Post 9648119)
Does the xtreme stock controller come with any wires or capacitors?
|
Originally Posted by hectickurt
(Post 9646796)
Hi Chris,
Yes I have both times I flashed it but still no blinky led at neutral Jason |
Originally Posted by jasonb
(Post 9648535)
The LED is realy hard to see unless it is quite dark. Also you need tohave the transmitter on so speedo has a neutral signal.
Jason Also the new V3 has the leds fixed in with the new soft switch which will be easier to see . |
Originally Posted by Benzaah
(Post 9646929)
Angelo, will you attend FEMCA next week in Sydney? Will be good to get some set up advice for the massive Whalan track where i expect our HW and 17.5 motors to be pushed to the max. It's interesting to hear you say how delay is essential on big tracks. Do you have settings to suggest? Heres a pic of what awaits us :D
http://img801.imageshack.us/img801/6909/picture597m.jpg ps: FDR was 5.0 For those that asked ... 1: For/Brake 2: 20% 3: 6.2v 4: 9 5: 100% 6: 25% 7: 0% 8: 6% 9: 40 10: 24 11: Enable 12: 24 13: 2000 14: 0.2 15: 300 |
Originally Posted by puiwc
(Post 9646799)
i am using hobbywing motor 10.5t
FDR 7.30/7.50 DRRS 9 Boost 44 Turbo ramp 12/0.1s turbo timing 20 start rpm 9000 rpm turbo delay 0.2s/0.3s timing acc 400/500rpm try the lower setup then change one at a time depending on the heat produce by motor, check the temp every 1.5/2mn and stop if the motor is getting too hot in any case but this should be a good start. You could use a fan on motor too (recommended) |
Originally Posted by Benzaah
(Post 9646929)
Angelo, will you attend FEMCA next week in Sydney? Will be good to get some set up advice for the massive Whalan track where i expect our HW and 17.5 motors to be pushed to the max. It's interesting to hear you say how delay is essential on big tracks. Do you have settings to suggest? Heres a pic of what awaits us :D
http://img801.imageshack.us/img801/6909/picture597m.jpg |
if anyone is interested. used following setup for an LRP x11 13.5T last weekend with 211 software. worked like a charm except for the brakes (which are not existend with this lrp motor, hopefully new software or esc will fix this aswell). good rip and top speed.
FDR 6,5 DRRS 9 Boost 50 Turbo ramp fastest turbo timing 14 start rpm 3000 rpm turbo delay 0.2s/0.3s timing acc 150 cooling fan |
Does there exist some manual for the ESC settings, when to use what and some more detail to learn to understand the settings and effects or is it basically trial and error. I do not have all the time in the world to find all out by myself so some good logic help or a guidance would be greatly appreciated
I run ia 120A speedpassion version modified on a TC and a 1S speedpassion version mod/stock and blinky 10.5 on a 12th scaler I guess some basic explanation might do the trick ;-) |
1 Attachment(s)
Originally Posted by Nilezb
(Post 9651248)
Does there exist some manual for the ESC settings, when to use what and some more detail to learn to understand the settings and effects or is it basically trial and error. I do not have all the time in the world to find all out by myself so some good logic help or a guidance would be greatly appreciated
I run ia 120A speedpassion version modified on a TC and a 1S speedpassion version mod/stock and blinky 10.5 on a 12th scaler I guess some basic explanation might do the trick ;-) I have attached the instructions to the thread . regards Angelo |
Originally Posted by tommi
(Post 9645387)
Hmm...I re-flashed my ESC yesterday with the zero_rev with much excitement to test out the FW, but I strongly believe that the "rev" is meant "reversed" in this case? My motor was running backwards, no matter what I do to my throttle setting (NOR/REV) on the Tx..:weird:
Thanks Angelo, can't wait for the new FW and new V3 ESC! |
Originally Posted by Barry_Hughes
(Post 9632076)
Hi Angelo can you answer a question please
using 211 stock does setting the turbo delay to off just allow the amount of turbo to come in straight away or does it actually turn the turbo feature off< If it allows the turbo to come in straight away what is the difference between the "off" and the "fastest" setting? I have heard it suggested that on 211 the turbo delay should be set to off hence the question. I am running 21.5T (as per the posts above) I thought that the turbo on the 211 software only activated after the boost rpm was achieved and all the boost was used up. eg; if you had 30 steps of boost timing and a 3000 rpm start with acc at 500 the turbo wouldn't cut in until the revs hit 18000 rpm????.. With a data logger in my car i discovered that with a delay on the turbo the car would complete its boost then delay before activating the turbo. |
Originally Posted by M7H 213 is not in the latest v1.63 usb link software package. 211 is the latest in that package. 213 is again, like 101224 only released here on the internet, and then also only by replacing some files in the v1.63 folder on your pc. (Do you remember Angelo? ) I believe the only difference between 211 and 213, is when the turbo is released. 211 releases his turbo after all set boost timing is reached. 213 releases his turbo after the turbo delay, so actually like 119 does it..... anyone knowing it better, please correct me if I am wrong
Originally Posted by COBRARACING
(Post 9424176)
You got me this time M7H i cant keep a secret from you ,you have a good memory .
yes two files car_esc_settings.db3 car_esc_version_control.ini The best I can get, after trying various changes is to get the turbo to kick in about halfway down the straight. Some of the settings I have tried to try and get the turbo to come in earlier... DDRS maxxed out. Less boost timing. No turbo delay. Lower ACC setting. Lower rollut. So... can someone please point me too, where I can get hold of the files Angelo mentioned above, and also a quick "how to guide" to get the 213 software onto my ESC, so my turbo will kick in after the full throttle delay and not wait for all the boost to be used up first. Thx |
By rollout I take it you mean gearing? What motor and what gearing are you running. You are going the right way but have you increased the slope as well or are you running 518 stock?
Originally Posted by SeanV
(Post 9655443)
.
I really need this 213 software. On my local track I find that the turbo isn't coming in quick enough down the straight and the I am being out accelerated at the start of the straight. The best I can get, after trying various changes is to get the turbo to kick in about halfway down the straight. Some of the settings I have tried to try and get the turbo to come in earlier... DDRS maxxed out. Less boost timing. No turbo delay. Lower ACC setting. Lower rollut. So... can someone please point me too, where I can get hold of the files Angelo mentioned above, and also a quick "how to guide" to get the 213 software onto my ESC, so my turbo will kick in after the full throttle delay and not wait for all the boost to be used up first. Thx |
| All times are GMT -7. It is currently 08:16 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.