EUREKA !!

Well for others that might have the same problems, after looking around this is what I did.

Loaded "old" Speed passion 1.02 version from SP site, loaded 1.02 instead of 617 (twice to be done and after a couple of tries) then open HW usb link, loaded version 1.07 110119 impossible to load 101224, well it is possible to load it on pro box but then it ask to update software when plugged into speedo, so far no luck to load it on, so I am back to 110211 which is fine as I race 10.5t.

one thing, you need to upgrade twice every version, it even stopped half way (error in communication) everytime I try to upgrade, just do it again.

Maybe someone can explain why the incompatibility to upgrade from 110119 to 101224 ?

At least now my program box says Hobbywing rather than Speed Passion and everything is back to normal.

Hi

Give us your full setup, you probably have a setting that is wrong, and what motor are you using?

My setup are :-
Xray T2 009
Hobby wing xtreme stock ESC with HobbyWing 17.5T motor senored
Vapextech 30C 2s 7.4v 36.5Wh 5000mah Lipo
on 27mhz reciever / tx ( will upgrading soon)

ESC:-
Hardware version: HW427_V1.0
Software version: V3.0_110119STOCK

Program box:-
Hardware version: HW310 V1.0
Software version:V1.07_110119

Esc setting is:-

Running mode: forward only with brake(*)
Drag brake force: 0%
low voltage cut off: 3.2%
"DDRS" start mode: Level 9
maximum brake force: 50%(*)
Maximum reserve force: 25%

inital brake force : 0%
netural range: 12% wide
Boost timing: 46 degrees
Turbo open time: 18%/0.1 sec
Overheat protection: enable
Turbo timing: 0 deg
Boost start RPM: 4000
Turbo open delay: 0.3 sec
Boost timing ACC: 350 rpm/deg

Well you have 0 turbo timing
try to put 15-20 turbo timing

reduce turbo time a little 12% and DDRS to 6

the rest is about right depending on your track and you could probably update speedo to version 211.

Thanks for suggestion, i just upgraded the fw to 211, and changed the setting.

The track is around 20m straight with very fast right hander, layout alway changes but straight stays same.

Do esc dont go into turbo mode when battery get low ?

I came first in final without boost :P

Looking for starting settings for 10.5 motor, medium size carpet track with medium grip. software would be stock 211. Or mayby use standard settings when i load software?

Would try to read 10 pages back.....

My advice would be:
Boost 40
Turbo 30
acc 150
delay 0.1
start rpm 1000

doesn`t matter which fdr...

Have one of these 60a with a 17.5T motor in my sons B4 buggy, ran fine for awhile and now runs at about half speed, any ideas???

Try to charge the battery

All so check the censor cable.Make sure the plugs are in correctly or try an other cable.I also had this problem my fdr was to high changed this and happy days.

Boost and turbo = 70, max is 64 I thought...
this sounds like your motor will get hot with this setup, especially if you run LRP X12 10.5t.
the best is to try this and check your temp after 2 minutes.
FDR should be around 7/8 and run 211

Cant upgrade!!!
 

Just loaded the disc from my 2 in 1 box and restarted the laptop. When i go on the link it says its found updates so i click to upload them but all it does is tell me that it failed. Over and over again!
Help me please. I want to get 119 mod on my 60amp 8.5 ezrun.
Thanks

Hi Scoop

Did you read my post above?
I had problem to load software, make sure that you choose again 119 from the list when you try to load the second time, as it might not give you that choice automatically.

Mod on a 60A, make sure you have everything well setup...

What is the version of link you have on compy?

Im a total computer numpty. Ive just followed what ever came up on the screen. It says i have 119 firmware but the only software option is 512 and it wont let you load 512 when 119 is the firmware!
Im lost:rolleyes:

I know I found all these software versions a bit of a nightmare to sort out.

Remove the software you loaded with disc first.

Go to HW site and download link usb V 1.63, then you should have 3 versions on, 119, 224,512.

upgrade to 119 if this is the one you want.

Do all this and get back to me.