R/C Tech Forums - Go-Tech Engines Thread

hi peoples
I'm looking for a new eng. and just found this Item number: 220373384347on the bay. I cant find much info on it, is it a good eng? what does the "factory mod" part include? I have run SIRIO NOVARISSI V-SPEC ect in the past how will this compare? thanks in advance.

This is not a " factory modified engine " Go Factory do not modify engines. That is a gen 5 with a stock gen 5 crank. Id assume this guy is saying this to get sales but i can assure you it is not modified.

Buy from a local dealer and get some sort of back up service and warranty.

Cheers MM

Tabushi

03-15-2009 03:43 PM

Quote:

Originally Posted by losi_alaska (Post 5552713)

Look what I scored on today from a friend of mine, it cost me 1 thunder tiger .61 airplane motor and a castle phoenix 60a esc. Everything in the go box is still plasti wrapped, come on D8T I can't wait Here is a pic

Congrats man !!

And you got the new 0801 pipe series ... im waiting for mine !!, that stinger now its reinforced, very good !!

cya,

Arushmen

03-15-2009 04:09 PM

Re-fuling problem

Hi, I have a 5 port go engine on my hyper 9, I used to drive in Bogota, 2.600 mts over sea level.
My problem is that every time tha I am re-fuling (pit stop) my engine flame out. every time.
What can I do?
I have changed: Glow pug, for 6 to 4, I have made shorter presure line.
?????????????

22Racer

03-15-2009 04:53 PM

Flameouts during pist stops are usually due to carb being too rich on the low speed. Is it the long lsn or short?

Rex

Arushmen

03-15-2009 05:27 PM

Quote:

Originally Posted by 22Racer (Post 5554619)

Flameouts during pist stops are usually due to carb being too rich on the low speed. Is it the long lsn or short?

Rex

Thanks Rex, but I am not able to understan you question?
what is lsn?

Arushmen

03-15-2009 05:31 PM

Quote:

Originally Posted by Arushmen (Post 5554687)

Thanks Rex, but I am not able to understan you question?
what is lsn?

If are you talking about "low speed nedle" How can I know if It is short o loger?
Thanks in advance

Tabushi

03-15-2009 05:50 PM

Arushmen,

I just answered your email sent to me today about this issue ... hope to help you,

cya !

Arushmen

03-15-2009 05:56 PM

Quote:

Originally Posted by Tabushi (Post 5554762)

Arushmen,

I just answered your email sent to me today about this issue ... hope to help you,

cya !

Thanks Pato, I hope see you at Brazil.

Brandon Powell

03-15-2009 06:06 PM

PTM Go Tech 5port

I ran my ProTwister modded - Go Tech 5port this Saturday at ReoRaceway in Indiana. I was top qualifier for the B-main, bumped to the A-main and finished 4th after a 20min main. I was most impressed with only 1 pit at the 10 minute mark. The Go Engine continues to be a reliable choice.

Thanks,
Brandon

tagalong_74

03-15-2009 07:46 PM

Quote:

Originally Posted by tagalong_74 (Post 5551719)

Ok guys have a question for ya. Just broke in my new Go 21.7port turbo. runs flawlessly. Now that I took the alluminum foil off, I'm wondering what temps are normal for that motor because this thing is spot on and with the body on after a full tank ran through im only getting to 190 deg F? That amazes me and was wondering if thats normal or not. Thanks again guys

Anyone Else!!!!!!!!!

gravediggermaxx

03-15-2009 07:54 PM

if anyone has a 5 or 7 port .21 for sell pm me thanks

22Racer

03-15-2009 08:49 PM

Quote:

Originally Posted by Arushmen (Post 5554699)

If are you talking about "low speed nedle" How can I know if It is short o loger?
Thanks in advance

The long low speed needle (lsn) will not pull all the way out of the orfice when you look in the carb while pulling the barrell of the carb open. (like going to wide open) The short lsn will pull out at around 1/2 throttle.

Rex

RETRO RC

03-16-2009 12:11 AM

Quote:

Originally Posted by Tabushi (Post 5554469)

Congrats man !!

And you got the new 0801 pipe series ... im waiting for mine !!, that stinger now its reinforced, very good !!

cya,

hey Pato why are you still waiting I've had mine well over 6 months now:eek:;)

The stinger isn't reinforced in the picture I believe it is just a reflection from the plastic shrink wrap

Adrian

All times are GMT -7. It is currently 12:18 AM.

Page 399 of 1009

399

Show 40 post(s) from this thread on one page