Team Magic G4
#7501
Tech Fanatic
iTrader: (12)
so in conclusion the new UFO2 clutch shoe is no better? how about the rest of G4+ upgrade, do u see the difference? coz i think many ppl who are thinking of these new options would like to know more b4 buying them.
#7502
Hi gansei, mind to share your view on the new G4+ rear sway bar? is it better than stock? or better than those previous mod like mugen? might consider this if its good. thanks.
so in conclusion the new UFO2 clutch shoe is no better? how about the rest of G4+ upgrade, do u see the difference? coz i think many ppl who are thinking of these new options would like to know more b4 buying them.
so in conclusion the new UFO2 clutch shoe is no better? how about the rest of G4+ upgrade, do u see the difference? coz i think many ppl who are thinking of these new options would like to know more b4 buying them.
i quess G4+ stock rear sway bar is the best!!
(i will buy it when TM korea import)
i must do more test for UFO2 clutch shoe.. and other option in this week.
(i reduced UFO2 clutch shoe diameter.. not tested yet)
i will update the final G4+ options's onpinion..
#7507
Tech Elite
iTrader: (10)
http://kodakhodak.blogspot.com/
just some more pics of the new engine, g4+ pics
enjoy - xfingers this weekend all goes well for test/break in and race day sundai
just some more pics of the new engine, g4+ pics
enjoy - xfingers this weekend all goes well for test/break in and race day sundai
#7508
Tech Elite
iTrader: (19)
Hi! G4S users and Daz..
this is my clutch activity test movie
i did same clutch setup what i suffered from UFO2 Shoe wear out in last weekend.
is it slip? is it too late meet?
it's only 0.3mm clutch gap..
please see the movie and give me advice.
http://tvpot.daum.net/clip/ClipViewB...able=undefined
this is my clutch activity test movie
i did same clutch setup what i suffered from UFO2 Shoe wear out in last weekend.
is it slip? is it too late meet?
it's only 0.3mm clutch gap..
please see the movie and give me advice.
http://tvpot.daum.net/clip/ClipViewB...able=undefined
#7509
Hi Gansei, in regards to the clutch movie. trying to set the clutch on a starter box is no good. it doesnt give the feeling as running on a track. i dont think setting the spring tension till the spring binds then back of 3/4 of a turn is a good thing to do. while on a test day, start with a .8mm spring tension setting, then gradually set the spring tension harder a bit at a time, till you get it to slip. then back off the clutch spring tension till you feel its right for track and grip conditions. if you run on the same track all the time then you will have that setting measured and noted for a low grip day or medium grip day. just a suggestion
i tried back of 1 turn in 0.3mm clutch gap.
But it was rather feel like hesitantly (not enough torque)
i did not clutch setup on starter box...
i tried only to show clutch meeting timing.. perhaps you think my clutch setup too hard..
i did same setup to my RC friends who run RRR with UFO Clutch.
(he also had NT1 clutch and test it by clutch gap 0.5mm)
(RRR UFO Clutch is mine.. i lend it to him)
he said the early starting is very smooth and acceleration is very good.
But NT1 clutch setup was very too much torque..
so he take a mistake frequently...
he like more UFO clutch than NT1's clutch.
finally.. he purchased RRR UFO Clutch system (NEW PRODUCT, it's not Mine)
#7510
kodakhodak!!
hi kodak hodak!!!
can you make G4S transformer (gif) by photoshop?
if you make it.. it will be very nice work!!!
can you make G4S transformer (gif) by photoshop?
if you make it.. it will be very nice work!!!
#7512
http://pds35.cafe.daum.net/image/27/.../468d9863a1cbd
http://pds32.cafe.daum.net/image/48/.../4685e99406f55
#7513
Tech Elite
iTrader: (10)
animation!! if it is difficult... only one picture like this..
http://pds35.cafe.daum.net/image/27/.../468d9863a1cbd
http://pds32.cafe.daum.net/image/48/.../4685e99406f55
http://pds35.cafe.daum.net/image/27/.../468d9863a1cbd
http://pds32.cafe.daum.net/image/48/.../4685e99406f55
i am sure the boys at work could do something but yes its difficult to dooooo, but let me brain storm some ideas, i am sure i can make something from something!
but Gansei YOU are OUR G4S - CRAZY MAn "BUT WE LUV YA"
#7514
Ill ask one of my 3D guys at work, as i am in the Graphics/web and gaming industry!
i am sure the boys at work could do something but yes its difficult to dooooo, but let me brain storm some ideas, i am sure i can make something from something!
but Gansei YOU are OUR G4S - CRAZY MAn "BUT WE LUV YA"
i am sure the boys at work could do something but yes its difficult to dooooo, but let me brain storm some ideas, i am sure i can make something from something!
but Gansei YOU are OUR G4S - CRAZY MAn "BUT WE LUV YA"
http://pds39.cafe.daum.net/image/4/c.../468db3590134d
http://pds33.cafe.daum.net/image/5/c.../468db2a86316d
http://pds33.cafe.daum.net/image/48/.../468db43776777
#7515
K14128(G4 Front Dual Adjustable Anti Roll Bar)
K14128 -1(G4 Front Dual Adjustable Anti Roll Bar)
anyone know what difference of these parts?
K14128 -1(G4 Front Dual Adjustable Anti Roll Bar)
anyone know what difference of these parts?