Kyosho v-one rrr
#7621
are you running the stock v one rr up rights ? if so you need to run 2deg off set rims to clear the up rights, if you are running the v one rrr ones you will need to get the vzw007 and run zero off set rims, or the stock wc ones(not sure on the part # and two deg off set rims.
another thing you can do and it is alot cheapr, get the 3r racing alum hex adapters in the 2 deg off set, with thses you ca run the stock axiles with the old style hubs and zero off set rims.
another thing you can do and it is alot cheapr, get the 3r racing alum hex adapters in the 2 deg off set, with thses you ca run the stock axiles with the old style hubs and zero off set rims.
#7622
Tech Initiate
well, i have 3racing rear universals. 2mm offset i believe.
i noticed theres was a spacer on each dogbone. so i placed the spacer in between the outter bearing and the pin/wheel hex. Is this not a good idea?
or can i use this as a permanent fix.
i noticed theres was a spacer on each dogbone. so i placed the spacer in between the outter bearing and the pin/wheel hex. Is this not a good idea?
or can i use this as a permanent fix.
#7623
Originally Posted by krnfx
well, i have 3racing rear universals. 2mm offset i believe.
i noticed theres was a spacer on each dogbone. so i placed the spacer in between the outter bearing and the pin/wheel hex. Is this not a good idea?
or can i use this as a permanent fix.
i noticed theres was a spacer on each dogbone. so i placed the spacer in between the outter bearing and the pin/wheel hex. Is this not a good idea?
or can i use this as a permanent fix.
#7624
Did anyone come up with a method to take the pinion gears off the light weight clutchbell without bending it? I know it was an issue before.
#7625
Tech Elite
Thread Starter
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
can anyone make a list of the difference between the v1rrr wce and the v1rrr evo? like the following: does the v1rrr evo come with 1 piece engine mount? universals? aluminum pipe holder? lightened 1st gear bearing, etc??? thanks
#7626
Originally Posted by doki_doki
can anyone make a list of the difference between the v1rrr wce and the v1rrr evo? like the following: does the v1rrr evo come with 1 piece engine mount? universals? aluminum pipe holder? lightened 1st gear bearing, etc??? thanks
The answer is no to all of your questions.
#7628
Originally Posted by Motorman
Ok Kyosho guru's I need a question answered. PN VZ115-23 is a first gear pinion for the RR and FW05. Will it fit Second gear on the RRR bell which I believe is has the same diameter threads on second as the RR and FW05 had on first.
http://www.kyosho.co.jp/web/products...r_060322-e.pdf
*and I have the part in hand. VZW066-23 (for RRR&FW05)
#7630
Originally Posted by Motorman
so you are saying that gear will actually fit second on the rrr
Did you change the part number question? I could have sworn you put VZW066-23. I still answered the question wrong though.
#7631
Originally Posted by doki_doki
can anyone make a list of the difference between the v1rrr wce and the v1rrr evo? like the following: does the v1rrr evo come with 1 piece engine mount? universals? aluminum pipe holder? lightened 1st gear bearing, etc??? thanks
#7632
Tech Master
iTrader: (1)
yes I did change the number the only difference between them is one is steel and the other is alumunium. I was told those gears would fit second on the RRR clutch bell even though they say first. Is the hole in them small like a regular 16 type pinion for the RRR or is it big like second?
could you measure the inside of the hole and tell me what it is?? On the one you have
could you measure the inside of the hole and tell me what it is?? On the one you have
#7633
Originally Posted by Motorman
yes I did change the number the only difference between them is one is steel and the other is alumunium. I was told those gears would fit second on the RRR clutch bell even though they say first. Is the hole in them small like a regular 16 type pinion for the RRR or is it big like second?
could you measure the inside of the hole and tell me what it is?? On the one you have
could you measure the inside of the hole and tell me what it is?? On the one you have
VZ115-23 or the steel version is the 2nd pinon gear for RRR. This same gear is used on the FW-05R/RR as the 1st pinon gear.
#7635
No Problem...