Kyosho v-one rrr
#7606
Tech Initiate
hey, i got the new rear hubs(v1RR) and i just realized i had to dremel some of the upright so that the rear tire rim would not be scraping the hub on the old hubs(i replaced both cause i realized that this weakens the hub making it more prone to breakage)
I realize that i can sort of "pop" my wheels outwards and gain about an aditional 10mm in width(which i dont mind ^^)
Do i need rims with 2 mm offset(i have rear universals with 2mm offset)
lol.. i bet this is and i just answered my own question ><
I realize that i can sort of "pop" my wheels outwards and gain about an aditional 10mm in width(which i dont mind ^^)
Do i need rims with 2 mm offset(i have rear universals with 2mm offset)
lol.. i bet this is and i just answered my own question ><
#7607
guys
Im having some problems with my brake I adjusted the screw until hold the disc, then I unscrewed a bit to run freely. The fuel line in the linkage is very short too, but I didnt found a good efficiency
I want a agressive brake
Any sugestion?
PS: 3racing disc original pads
thanks a lot
Im having some problems with my brake I adjusted the screw until hold the disc, then I unscrewed a bit to run freely. The fuel line in the linkage is very short too, but I didnt found a good efficiency
I want a agressive brake
Any sugestion?
PS: 3racing disc original pads
thanks a lot
#7608
Tech Initiate
are they new? if so theyll need to be broken in just like disk brakes on a bike
#7609
yes they are new
I ran about 15 tanks
I ran about 15 tanks
#7611
I used subtrim and EPA I placed a little course because the servo was pushing the entire rear
There is more fuctions on brakes? I have a 3PKS
There is more fuctions on brakes? I have a 3PKS
#7612
Tech Initiate
what offset tired should i be using if the tire is scraping the hub?
#7613
Tech Master
iTrader: (3)
Join Date: Dec 2001
Location: Costa Del Sol, Marbella, Spain www.bradir.net
Posts: 1,456
Trader Rating: 3 (100%+)
hubs
Originally Posted by krnfx
hey, i got the new rear hubs(v1RR) and i just realized i had to dremel some of the upright so that the rear tire rim would not be scraping the hub on the old hubs(i replaced both cause i realized that this weakens the hub making it more prone to breakage)
I realize that i can sort of "pop" my wheels outwards and gain about an aditional 10mm in width(which i dont mind ^^)
Do i need rims with 2 mm offset(i have rear universals with 2mm offset)
lol.. i bet this is and i just answered my own question ><
I realize that i can sort of "pop" my wheels outwards and gain about an aditional 10mm in width(which i dont mind ^^)
Do i need rims with 2 mm offset(i have rear universals with 2mm offset)
lol.. i bet this is and i just answered my own question ><
what brand of aluminum wheel hexes are you using? kawahara or 3racing style alum hexes eliminates this prob or the kyosho optional silver outdrives with spacer will help . du u have a pic of your rear hubs?
#7614
Tech Initiate
i use the stock plastic wheel adapters.
#7615
Tech Initiate
would mugen MTX-4 (Aluminum Wheel Hub MTX4
# T0142) fit on my V1RR?
# T0142) fit on my V1RR?
#7616
Tech Elite
iTrader: (4)
Originally Posted by jeff1
I used subtrim and EPA I placed a little course because the servo was pushing the entire rear
There is more fuctions on brakes? I have a 3PKS
There is more fuctions on brakes? I have a 3PKS
Hope this helps.
Dom
#7617
Tech Initiate
is the popping that occurs in my rear tires normal? ie: being able to pop the rear tires out and gain a few mm of width and being able to pop them back in
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
#7618
Tech Elite
iTrader: (4)
Originally Posted by krnfx
is the popping that occurs in my rear tires normal? ie: being able to pop the rear tires out and gain a few mm of width and being able to pop them back in
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
Dom
#7619
Tech Master
iTrader: (3)
Join Date: Dec 2001
Location: Costa Del Sol, Marbella, Spain www.bradir.net
Posts: 1,456
Trader Rating: 3 (100%+)
popping question
Originally Posted by krnfx
is the popping that occurs in my rear tires normal? ie: being able to pop the rear tires out and gain a few mm of width and being able to pop them back in
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
popping out the tires? what do u mean? and i suggest using aluminum hexes, not sure of the mugen part
ian
#7620
Originally Posted by krnfx
is the popping that occurs in my rear tires normal? ie: being able to pop the rear tires out and gain a few mm of width and being able to pop them back in
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><
in a race which measurement would they take, popped out or popped in? lol sorry for the noob questions ><