Team Associated TC4
Anybody Racing their tc4's at the Snowbirds or Roar nationals ???
Tech Fanatic
I won't make it, but you can use the upgrades on this thread's post #10888 to get your Car ready... Which class will you run ???
I am always available here....
If someone runs vta please post a setup. I would love to see a something newer then 2006 posted
Tech Fanatic
http://gregrojna.com/trash/2013/tc4%20birds.pdf
2013 SNOWBIRDS coverage
Tech Regular
iTrader: (19)
I just got a job that's next door to an always vacant, large and very nicely paved parking lot.
I'd like a good on-road car that I can take over there after work and have fun with. I'd also like this same car, if possible, to be changed over and setup for two purposes: drifting and racing - nothing serious, just for having fun.
Now, here come the stupid questions:
#1 - would it be possible to setup this car to do both drifting and on-road handling? I know I'd have to have different tires - what else?
#2 - It seems like a one-way front diff and locked rear would be good choices for drifting but can the shaft-driven TC4 be modified this way?
#3 - Could I use just one brushless motor & ESC for both drifting and road racing?
#4 - I have a boatload of 2200 mAh 3S lipos - could I use these with a brushless setup?
Thank you
I'd like a good on-road car that I can take over there after work and have fun with. I'd also like this same car, if possible, to be changed over and setup for two purposes: drifting and racing - nothing serious, just for having fun.
Now, here come the stupid questions:
#1 - would it be possible to setup this car to do both drifting and on-road handling? I know I'd have to have different tires - what else?
#2 - It seems like a one-way front diff and locked rear would be good choices for drifting but can the shaft-driven TC4 be modified this way?
#3 - Could I use just one brushless motor & ESC for both drifting and road racing?
#4 - I have a boatload of 2200 mAh 3S lipos - could I use these with a brushless setup?
Thank you
Red Sand, you can get a tc4 club racer with a 3s capable tekin RS esc and a 17.5t tekin gen 1 motor.... All you'll need to do is tighten the tc4 rear diff when drifting, and loosen it when Racing !
You can't get belt cars in this case because of the peebles....
You can't get belt cars in this case because of the peebles....
Tech Elite
iTrader: (73)
TC4 Pinion
What is the largest pinion that can be installed in the TC4 Club Racer. To get the gear ratio needed for 21.5 VTA (Australia) I need to get to below 3:1.
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Last edited by Andrew Barr; 01-27-2013 at 02:58 AM.
Tech Regular
What is the largest pinion that can be installed in the TC4 Club Racer. To get the gear ratio needed for 21.5 VTA (Australia) I need to get to below 3:1.
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Tech Elite
iTrader: (73)
Tech Addict
What is the largest pinion that can be installed in the TC4 Club Racer. To get the gear ratio needed for 21.5 VTA (Australia) I need to get to below 3:1.
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Because in the internal drive ratio is 2.5:1, 48 pitch cant get low enough and I have to resort to 64 pitch. Looks like I will need a 58T 64P pinion and a 76T spur (may need to go lower).
Has anyone been able to fit a 58T pinion? BTW, I am aware that I will need to grind away part of the chassis as shown in the manual.
Thanks
Tech Elite
iTrader: (73)
Tech Adept
Anyone know where I can get a composite main shaft for the car??
Only place I have found them is on RC-mushroom.
Only place I have found them is on RC-mushroom.