Yokomo MR-4TC SD
#2822
Tech Initiate
Originally posted by lonestar1127
.
.
Would you know if the rayspeed edition be available as a complete kit or just the chassis?
Thanks.
#2824
Tech Initiate
Originally posted by lonestar1127
i'm not too sure.... i tink it would be selling as hop ups under RaySpeed
i'm not too sure.... i tink it would be selling as hop ups under RaySpeed
#2825
Tech Fanatic
iTrader: (53)
Originally posted by Matt Howard
I'm sure there's a couple people still running the old car but the vast majority of yokomo drivers are running the SD car now, It's by far easier to work on and setup.
I'm sure there's a couple people still running the old car but the vast majority of yokomo drivers are running the SD car now, It's by far easier to work on and setup.
#2826
Tech Master
Originally posted by Explorer
Hi Lonestar,
Would you know if the rayspeed edition be available as a complete kit or just the chassis?
Thanks.
Hi Lonestar,
Would you know if the rayspeed edition be available as a complete kit or just the chassis?
Thanks.
#2827
Mid-turn understeer
Hi guys,
I raced with my SD yesterday and I was very happy with the setup of the car. Very easy and smooth to drive. The only thing
I couldnīt get rid of was some mid-turn understeer.
Turn-in and corner exit were quite perfect.
Drove the car with 2 diffs. no swaybars. rear:green springs
front: yellow, 40wt f+r, 3 degree rear toe-in.
Any suggestions?
Thanks,
IH
I raced with my SD yesterday and I was very happy with the setup of the car. Very easy and smooth to drive. The only thing
I couldnīt get rid of was some mid-turn understeer.
Turn-in and corner exit were quite perfect.
Drove the car with 2 diffs. no swaybars. rear:green springs
front: yellow, 40wt f+r, 3 degree rear toe-in.
Any suggestions?
Thanks,
IH
#2830
Jeff,
The over- all car felt pretty good just the rear of the car was a little loose. I took the rear sway bar after the last race.
What set up did you use at Mike's track and spur gear.
Caleb
The over- all car felt pretty good just the rear of the car was a little loose. I took the rear sway bar after the last race.
What set up did you use at Mike's track and spur gear.
Caleb
#2831
Jeff W,
Are u still using AE springs? Have you change your set up from Mike's
Are u still using AE springs? Have you change your set up from Mike's
#2832
Hello folks,
The kit included some extra spacers, are those to be used to raise the front roll center and rear roll center? You just place them under the hinge mounts/ suspension mounts.
The kit included some extra spacers, are those to be used to raise the front roll center and rear roll center? You just place them under the hinge mounts/ suspension mounts.
#2833
Tech Elite
iTrader: (30)
Yodace, I used the spacers included in the kit. Just remove the screws and slide the washer under the mount...real simple tuning change, make sure you readjust droop.
The changes I made to my car are for a concrete surface with less bite then Mike's. I ran Gold front, Blue rear with 40wt. at Mike's. I think if you try the roll center change you will be pretty happy!
Jeff
The changes I made to my car are for a concrete surface with less bite then Mike's. I ran Gold front, Blue rear with 40wt. at Mike's. I think if you try the roll center change you will be pretty happy!
Jeff
#2834
Jeff W.
Did you but the spacers in the rear hinge pin carriers ? Are you still using AE springs? So tell me again want the spacer do for the car. Please.
Caleb
Did you but the spacers in the rear hinge pin carriers ? Are you still using AE springs? So tell me again want the spacer do for the car. Please.
Caleb
#2835
Tech Elite
iTrader: (3)
Originally posted by yodace
Jeff W.
Did you but the spacers in the rear hinge pin carriers ? Are you still using AE springs? So tell me again want the spacer do for the car. Please.
Caleb
Jeff W.
Did you but the spacers in the rear hinge pin carriers ? Are you still using AE springs? So tell me again want the spacer do for the car. Please.
Caleb