|
Originally Posted by J_Bone
(Post 10607774)
YUP!! one on each side!!
|
I'll try my best to make it. It depends on traffic.:flaming: I should get there about 6:00-6:15. No practice, but get to setup before first heat.
|
Originally Posted by J_Bone
(Post 10607796)
I'll try my best to make it. It depends on traffic.:flaming: I should get there about 6:00-6:15. No practice, but get to setup before first heat.
|
Sounds good!
You running the 0 hole(drilled) on the rear tower? |
Originally Posted by GSM Storm
(Post 10604219)
Hi all
What diff oil weight should I run in the gear diff. Regards Gary 4000wt is my 2 cents on that topic |
Originally Posted by Brian L
(Post 10606780)
Was on my list of things to try. I usually liked a little heavier pack in my truck, so it wasn't at the top of my list. A new adddition will be keeping me away for a little bit now.
I should have a new FTSC10 @ the track this Friday. Switching back to SCT for the summer. On the fence whether to sell my shorties or try them in the truck. CSR |
Originally Posted by vw addict
(Post 10605294)
My ball diff feels like gravel after a few practice runs, was butter smooth after I built it following racer53's vids. What did I do wrong?
Slipper is to tight. |
Originally Posted by kc_nitro_rc
(Post 10609189)
Slipper is to tight.
:weird: |
Took 3rd in the 17.5 class at the JC race this weekend! Truck was dialed.
https://fbcdn-sphotos-a.akamaihd.net...90639899_n.jpg https://fbcdn-sphotos-a.akamaihd.net...37807205_n.jpg |
Avid Bearings
Wondering what type to order. They offer revolution or rubber sealed. Thanks for the input.
|
beautiful truck and grats
Originally Posted by 1Fastpede
(Post 10609240)
Took 3rd in the 17.5 class at the JC race this weekend! Truck was dialed.
https://fbcdn-sphotos-a.akamaihd.net...90639899_n.jpg https://fbcdn-sphotos-a.akamaihd.net...37807205_n.jpg |
Originally Posted by Murray100
(Post 10609512)
Wondering what type to order. They offer revolution or rubber sealed. Thanks for the input.
|
Originally Posted by vw addict
(Post 10605294)
My ball diff feels like gravel after a few practice runs, was butter smooth after I built it following racer53's vids. What did I do wrong?
I can get two race days using ceramic balls before mine feels like gravel. The fix is to remove the thrust bearing assembley, clean the parts, resand the washers with something like 320 sandpaper (till the groove where the balls ride disapear), regrease, and reinstall. It's free, but it's a pain. |
Originally Posted by vw addict
(Post 10605294)
My ball diff feels like gravel after a few practice runs, was butter smooth after I built it following racer53's vids. What did I do wrong?
http://www.rcshortcourse.com/forum/t...fect-diff.html |
Originally Posted by 1Fastpede
(Post 10609240)
Took 3rd in the 17.5 class at the JC race this weekend! Truck was dialed.
https://fbcdn-sphotos-a.akamaihd.net...90639899_n.jpg https://fbcdn-sphotos-a.akamaihd.net...37807205_n.jpg |
| All times are GMT -7. It is currently 04:54 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.