BMI's DB12R
#4337
i dont know if the old one fits but the new serpent front end looks pretty bitchin now back to my cave
#4338
Well I talked with Marty Today and he said the DB12R will be on its way soon!
I for one can not wait!
There are 5 of us that are going to race and test the top 5 1/12 scale cars out there today. We will be running cells only 4600's and Brushless SP GT seires. and WindTunnel's 962 Bodies (Painted up with the old time Livery) and we will also be running a 13.5 BL motor, Question is this Good for 1/12 scale or would a 10.5 be better, New to 1/12 scale.
Club Racing! same bodies same motors same batteries. 5 cars, Fun!!!!!!!!!
C.C.
I for one can not wait!
There are 5 of us that are going to race and test the top 5 1/12 scale cars out there today. We will be running cells only 4600's and Brushless SP GT seires. and WindTunnel's 962 Bodies (Painted up with the old time Livery) and we will also be running a 13.5 BL motor, Question is this Good for 1/12 scale or would a 10.5 be better, New to 1/12 scale.
Club Racing! same bodies same motors same batteries. 5 cars, Fun!!!!!!!!!
C.C.
Last edited by Cunningham1972; 03-12-2008 at 05:58 PM.
#4339
#4340
just tryin to catch up with school bud. a week after the Birds i went out to AZ for the nitro challenge for another whole week. when is the enxt on-raod race over in tampa??
#4341
Tech Regular
iTrader: (6)
sorry to bug you guys but,
i need some help..... i just purchased a db12r and am in need of some starting set-up points....
i am fairly new to 1/12, only been running since november.... i was running a 12l4 with the .063" t-bar and dbl pinks up front and whites in the rear. our carpet isnt even a year old as it was purchased in october and it isnt a permanent track
ok so the info i need is a starting point for tires.... all we have around here is jaco's and pretty much every current compound is available.
also wondering what servo you guys use.... i was using a hitec 225mg but it wont fit in the mounts.... which is the prfered servo the futaba 9602 or the 9650?
again sorry to bug all you guys but any help would be greatly appreciated
i need some help..... i just purchased a db12r and am in need of some starting set-up points....
i am fairly new to 1/12, only been running since november.... i was running a 12l4 with the .063" t-bar and dbl pinks up front and whites in the rear. our carpet isnt even a year old as it was purchased in october and it isnt a permanent track
ok so the info i need is a starting point for tires.... all we have around here is jaco's and pretty much every current compound is available.
also wondering what servo you guys use.... i was using a hitec 225mg but it wont fit in the mounts.... which is the prfered servo the futaba 9602 or the 9650?
again sorry to bug all you guys but any help would be greatly appreciated
#4342
Tech Fanatic
iTrader: (2)
hey lorider. start with the kit setup it works very good. run jaco lilac up front and yellow or gray rear. run shurlube in the tubes #3 or #4 and on front king pins. use the futaba 9650 or ko 949 they fit perfect and are top notch. mount it flat with the medium height ballstuds on the steering knuckles. stock flex plates with no set screws. if you need more steering use tall ball stud on antenna mount to make shock flatter also can try red or copper spring. have fun buddy. you will love this car. any questions feel free to ask or pm me.
#4344
Tech Regular
iTrader: (6)
i tried purple fronts on my 12l4 and couldnt get it to turn no matter what else i did. I think we got a set of lilacs floating between pit boxes so maybe i will give those a try.
thanks for the help, hopefully i can get this little bugger set-up over the weekend and ready for racing
thanks for the help, hopefully i can get this little bugger set-up over the weekend and ready for racing
#4347
Tech Champion
Are the BMI guys traveling to a race or something? Haven't seen a post from them in a few days.
#4348
Tech Lord
iTrader: (13)
No traveling here. I have been very busy and havent been able to post much. Once i get some of my work done and im not hammered when i get home, I will be up here helping out again. Thanks for everyone helping out answering questions while i am behind. Its cool to be able have the support from you guys.
#4349
#4350
Tech Champion
No traveling here. I have been very busy and havent been able to post much. Once i get some of my work done and im not hammered when i get home, I will be up here helping out again. Thanks for everyone helping out answering questions while i am behind. Its cool to be able have the support from you guys.