R/C Tech Forums

Go Back  R/C Tech Forums > General Forums > Nitro Off-Road > Offroad Nitro Engine Forum
NOVAROSSI Engine thread.... >

NOVAROSSI Engine thread....

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Like Tree352Likes

NOVAROSSI Engine thread....

Thread Tools
 
Search this Thread
 
Old 09-09-2012 | 11:49 AM
  #3841  
merdith6's Avatar
merdith6
Tech Elite
iTrader: (3)
 
Joined: Oct 2009
Posts: 2,350
From: Brazoria, TX
Default well
Originally Posted by dia
Hi guys. Can you please help out!! A back plate screw on my engine was decapitated.... and there is no way to take it out. So I'm looking for another crankase at a reosonable price. I found one from a bonito 21-7xlb/a(part # 09029tn11) where as the toro neros is 09029tn. Does anyone know if it will be ok? Will my engine seal if I use lucky7 sealant and 3 out of 4 screws?
Any ideas? Thank you for in advance for any replies provided.
I had that happen once and if you try to get it out it could cause more problems. I say seal it up and run it. It worked for me.
merdith6 is offline  
Reply
Old 09-09-2012 | 01:04 PM
  #3842  
houston's Avatar
houston
Tech Prophet
iTrader: (96)
 
Joined: Sep 2004
Posts: 15,844
From: Sherwood,OR
Default
Originally Posted by dia
Hi guys. Can you please help out!! A back plate screw on my engine was decapitated.... and there is no way to take it out. So I'm looking for another crankase at a reosonable price. I found one from a bonito 21-7xlb/a(part # 09029tn11) where as the toro neros is 09029tn. Does anyone know if it will be ok? Will my engine seal if I use lucky7 sealant and 3 out of 4 screws?
Any ideas? Thank you for in advance for any replies provided.
i have a couple toro nero cases , i will make you a pretty good deal , just lmk
houston is offline  
Reply
Old 09-11-2012 | 06:53 AM
  #3843  
jnorwood_losi's Avatar
jnorwood_losi
Tech Regular
iTrader: (10)
 
Joined: Feb 2012
Posts: 434
Default Bearing question
I am putting new bearings in my Bonito, the new 17011 Nova bearing I have has a clear looking seal on the side that would face the inside of the engine, but the one I pulled out does not have this. Is it something I need to take out????
Thanks
jnorwood_losi is offline  
Reply
Old 09-11-2012 | 04:01 PM
  #3844  
jnorwood_losi's Avatar
jnorwood_losi
Tech Regular
iTrader: (10)
 
Joined: Feb 2012
Posts: 434
Default
Originally Posted by jnorwood_losi
I am putting new bearings in my Bonito, the new 17011 Nova bearing I have has a clear looking seal on the side that would face the inside of the engine, but the one I pulled out does not have this. Is it something I need to take out????
Thanks
Anyone know the answer?
jnorwood_losi is offline  
Reply
Old 09-11-2012 | 04:17 PM
  #3845  
transplantlife
Tech Elite
iTrader: (47)
 
Joined: Oct 2008
Posts: 2,355
From: Chicago, IL/St.Petersburg,FL
Default
guys been looking at the novas had a question is there much difference between the BTT vs the +4 team?
transplantlife is offline  
Reply
Old 09-11-2012 | 06:05 PM
  #3846  
beidle99's Avatar
beidle99
Tech Master
iTrader: (9)
 
Joined: Jan 2005
Posts: 1,932
From: Woodbury, NJ
Default
Originally Posted by transplantlife
guys been looking at the novas had a question is there much difference between the BTT vs the +4 team?
I have a Btt. in running, the Btt will have a slight edge in top speed while the team has a little more bottom. Run either with a 2058, 9901, or 2096. The 2096 will give you great bottom end, top end and run time My btt with the 2096 pipe feels like an electric without the crazy wheel spin. It just squats and goes. Some guys have been talking about a 2032 pipe I believe, but they are hard to come by.
beidle99 is offline  
Reply
Old 09-11-2012 | 06:08 PM
  #3847  
beidle99's Avatar
beidle99
Tech Master
iTrader: (9)
 
Joined: Jan 2005
Posts: 1,932
From: Woodbury, NJ
Default
Originally Posted by jnorwood_losi
Anyone know the answer?
I would leave the seal on, but I know the bearing that came in my plus 4 (not a 17011 as advertised) had that seal and the 17011 I put in did not have the seal. Maybe ask over on the HES thread. Monty knows the bearings pretty good.
beidle99 is offline  
Reply
Old 09-11-2012 | 06:33 PM
  #3848  
jnorwood_losi's Avatar
jnorwood_losi
Tech Regular
iTrader: (10)
 
Joined: Feb 2012
Posts: 434
Default
None of them are online, it seems weird though. I triple checked the NOVAROSSI and its a 17011. The one that came out SHOULD be a 17011...I am about to put the bearings in now, I keep leaning towards pulling this seal on the inside, as it would lube better...i dunno
jnorwood_losi is offline  
Reply
Old 09-11-2012 | 06:46 PM
  #3849  
rider313's Avatar
rider313
Tech Elite
iTrader: (94)
 
Joined: Sep 2009
Posts: 4,436
From: MN
Default
I would Leave it on.
rider313 is offline  
Reply
Old 09-11-2012 | 07:25 PM
  #3850  
houston's Avatar
houston
Tech Prophet
iTrader: (96)
 
Joined: Sep 2004
Posts: 15,844
From: Sherwood,OR
Default
Originally Posted by jnorwood_losi
None of them are online, it seems weird though. I triple checked the NOVAROSSI and its a 17011. The one that came out SHOULD be a 17011...I am about to put the bearings in now, I keep leaning towards pulling this seal on the inside, as it would lube better...i dunno
Thats not a "seal" , its the ball cage
houston is offline  
Reply
Old 09-11-2012 | 08:21 PM
  #3851  
jnorwood_losi's Avatar
jnorwood_losi
Tech Regular
iTrader: (10)
 
Joined: Feb 2012
Posts: 434
Default
Originally Posted by houston
Thats not a "seal" , its the ball cage
Ok, leave it on or pull it out? Thanks Monty
jnorwood_losi is offline  
Reply
Old 09-11-2012 | 09:26 PM
  #3852  
hambone's Avatar
hambone
Tech Elite
iTrader: (1)
 
Joined: Aug 2008
Posts: 2,436
From: Bloomsburg, Pa.
Default
It's what keeps the balls in place. If you pull it out the bearing will fall apart.
hambone is offline  
Reply
Old 09-11-2012 | 09:40 PM
  #3853  
jnorwood_losi's Avatar
jnorwood_losi
Tech Regular
iTrader: (10)
 
Joined: Feb 2012
Posts: 434
Default
Thanks Rob I left it in and its back together, I dont get why the one that came out did not have it and the new one did...while the other guy that replied earlier said his was vice versa and his new one did not have it....I thought it was all the 17011
Ahh well.
YOU GOING TO LCRC SATURDAY???
jnorwood_losi is offline  
Reply
Old 09-11-2012 | 09:45 PM
  #3854  
hambone's Avatar
hambone
Tech Elite
iTrader: (1)
 
Joined: Aug 2008
Posts: 2,436
From: Bloomsburg, Pa.
Default
I just got back from LCRC, lol. I'll probably be there sat.
hambone is offline  
Reply
Old 09-11-2012 | 10:36 PM
  #3855  
Guillermito's Avatar
Guillermito
Tech Regular
 
Joined: Aug 2010
Posts: 286
From: Argentina
Default
Hello, someone tested the engines "Pre-Run"? How many tanks need to be ready for a race?

Thanks. Best Regards.
Guillermito is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.