R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: trilerian
Showing results 1 to 25 of 500
Search took 0.06 seconds.
Forum: Radio and Electronics
05-12-2024, 11:00 AM
Replies: 35
Views: 2,537
Posted By trilerian

Do you want the quick answer or the long winded...

Do you want the quick answer or the long winded one?
I'll start with the quick answer. I would leave the timing in the same spot and test. Then I would drop the timing by a degree or two...
Forum: Radio and Electronics
05-10-2024, 10:09 AM
Replies: 10
Views: 588
Posted By trilerian

Actually that does make sense. The balance port...

Actually that does make sense. The balance port also senses the actual voltage of the battery and not just what the charger is putting out. In other words, there is a voltage drop across the...
Forum: Radio and Electronics
05-06-2024, 06:38 PM
Replies: 165
Views: 35,106
Posted By trilerian

Any progress on this? EDIT: And do you have the...

Any progress on this?
EDIT: And do you have the Simple Dyno software? I checked the github link, but there is not a packaged zip file that I can find.
EDIT: And sometimes you just got to click a...
Forum: Radio and Electronics
05-05-2024, 04:59 PM
Replies: 5
Views: 430
Posted By trilerian

All terminals I have seem sit below the plastic...

All terminals I have seem sit below the plastic case, so it is unlikely. However, if you want to be extra safe just get some 4mm or 5mm rubber stems to put in the terminals.
Forum: Electric On-Road
05-03-2024, 05:32 PM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

I did not measure it. I’m happy for the extra...

I did not measure it. I’m happy for the extra material…

Here is a pic with the arms stacked on top of each other. This was how I noticed it. To note, my car came from the 3rd batch of orders. So...
Forum: Electric On-Road
05-03-2024, 04:56 PM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

It isn’t a big change. I only noticed because I...

It isn’t a big change. I only noticed because I was making sure the arm was the right length and put them back to back.

New arm is on the right.
...
Forum: Electric On-Road
05-03-2024, 08:41 AM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

Finally got all my parts to put my car back...

Finally got all my parts to put my car back together. Interesting discovery... I bought a set of arms, C204-S. I thought these were a direct replacement for the stock arms (well, I guess they...
Forum: Radio and Electronics
05-02-2024, 09:54 AM
Replies: 35
Views: 2,537
Posted By trilerian

I would like to clarify my experience with my R1....

I would like to clarify my experience with my R1. My motor was used for testing purposes and was soldered onto multiple times before the insulator ring started coming apart. Personally, I have not...
Forum: Radio and Electronics
05-01-2024, 01:08 PM
Replies: 35
Views: 2,537
Posted By trilerian

Did they send out a new stator? I actually asked...

Did they send out a new stator? I actually asked them if they could just replace an insulator ring an their response was no. That design is not the best. I used some golf shaft epoxy I had laying...
Forum: Radio and Electronics
05-01-2024, 09:15 AM
Replies: 35
Views: 2,537
Posted By trilerian

It has not been my experience that the R1 rotors...

It has not been my experience that the R1 rotors are very strong. I have 5 R1 v21 motors of different flavors and the strongest rotor I have is 1720. Rotors are a crapshoot with R1 though, they...
Forum: Radio and Electronics
04-29-2024, 08:07 PM
Replies: 65
Views: 40,854
Posted By trilerian

That is not an issue I am having. Although I...

That is not an issue I am having. Although I still haven't had much of a chance to mess with it. I have been absolutely swamped lately. But I am almost caught up on work, so we'll see.
I will...
Forum: Radio and Electronics
04-28-2024, 10:41 PM
Replies: 536
Views: 189,294
Posted By trilerian

You should still be able to get close to 30A with...

You should still be able to get close to 30A with the 5 1ohm resistors. I just wired up a discharge bank in series to my 308 and was able to get 26-27A with a bank of 5 1ohm resistors. The way the...
Forum: Radio and Electronics
04-28-2024, 07:40 AM
Replies: 10
Views: 588
Posted By trilerian

As stated above it shouldn't make a difference...

As stated above it shouldn't make a difference while charging. But for an IR check, yes, you can just connect the sensor lead to the positive side on the battery. DRC sells a 1s/2s switch and its...
Forum: Radio and Electronics
04-25-2024, 07:42 AM
Replies: 165
Views: 35,106
Posted By trilerian

Do you tell the program the update time or does...

Do you tell the program the update time or does it take it from the timestamps of the readings?
If you are telling it the update time then this:
if((currentTime - lastUpdateTime) >...
Forum: Radio and Electronics
04-23-2024, 02:57 PM
Replies: 165
Views: 35,106
Posted By trilerian

How big is your encoder wheel? I can print one...

How big is your encoder wheel? I can print one in PETG, or even PA6-GF. Haven't had a chance to print with the PA6 yet, but it is supposed to be dimensionally stable.

Would you care to share...
Forum: Radio and Electronics
04-22-2024, 06:30 PM
Replies: 165
Views: 35,106
Posted By trilerian

Your angular velocity will be the same no matter...

Your angular velocity will be the same no matter where you are on the disc. Linear velocity will change, but that will not matter.
Do you have any gear reduction at all in the setup? 15ms is...
Forum: Radio and Electronics
04-21-2024, 06:27 PM
Replies: 165
Views: 35,106
Posted By trilerian

In a couple more weeks I should have some time...

In a couple more weeks I should have some time available to look into this as well. I have a bunch of different dev boards that can be tried. I can use the MiniPro flywheel and base for the...
Forum: Electric On-Road
04-20-2024, 11:10 PM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

I use a body reamer. I start with a hobby knife...

I use a body reamer. I start with a hobby knife to mark the spot, and then use the reamer.
Forum: Radio and Electronics
04-18-2024, 09:29 AM
Replies: 536
Views: 189,294
Posted By trilerian

While Roelof post will definitely get you to some...

While Roelof post will definitely get you to some usable values, personally I would use 5 x 0R5 (0.5 ohm) 100W resistors. You can get away with 50W, but the 100W will stay quite a bit cooler and...
Forum: Radio and Electronics
04-18-2024, 05:12 AM
Replies: 536
Views: 189,294
Posted By trilerian

If you want to, you just wire the positive of the...

If you want to, you just wire the positive of the fan between the battery positive and the resistor bank, then the negative to the negative. However doing this you are only going to get 3.2-4.2V for...
Forum: Radio and Electronics
04-17-2024, 09:50 PM
Replies: 536
Views: 189,294
Posted By trilerian

Parallel will look like train tracks. Line the...

Parallel will look like train tracks. Line the resistors up longitudinally adjacent and run a wire down both ends. Series would be your old school string of Christmas lights.

But in this case you...
Forum: Radio and Electronics
04-17-2024, 05:16 AM
Replies: 144
Views: 21,334
Posted By trilerian

There are way too many caveats to say that amps...

There are way too many caveats to say that amps and torque are directly proportional. There is a correlation between startup amps and startup torque but it is dependent on other variables as well....
Forum: Radio and Electronics
04-16-2024, 08:21 AM
Replies: 165
Views: 35,106
Posted By trilerian

Did you use the first sketch you posted, the...

Did you use the first sketch you posted, the original from Simple Dyno? Can you get the info using a terminal emulator instead of Simple Dyno? With the IDE open and a USB connected can you see the...
Forum: Electric On-Road
04-16-2024, 07:11 AM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

I'm not sure the tiniest of drops is good enough....

I'm not sure the tiniest of drops is good enough. The other guy I was running with used blue Loctite paste and one of his came apart in the main.

Regardless, I'm going back to the old versions...
Forum: Electric On-Road
04-15-2024, 04:07 PM
Replies: 6,837
Views: 2,066,390
Posted By trilerian

Call it OCD if you want, I don't have a rational...

Call it OCD if you want, I don't have a rational explanation. Well, I do, but not one most likely accepted by the masses.
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.