Originally Posted by Robudda723 (Post 9513549)

Anyone have any direct contact for Speed Passion.

I have been trying for over a month to get an RMA number on the web site and constantly get a Internal 500 error every time I hit submit. I have tried on 2 machines at 2 different locations with 3 different browsers and same thing. So started sending emails the last couple weeks asking for an RMA number and explaining what is going on, and no response. Then this last week I start to call because my warranty is up soon, They answer take my name and number and say they will call back and never do.

Seriously this is ridiculous. Any Ideas on how to get them actually do something and fix my stuff.

Rob

Originally Posted by John C (Post 9514105)

Robudda 723 you might try this # 888-928-1328, can get ahold of them but not sure you can get any service, I 've had my speedo sent in for 5 months, had to resend warranty card & receipt twice & still have no speedo.

Originally Posted by Raul Garcia (Post 9506349)

Go with the 2.1 Pro Stock, for the b4.1. It runs anything you want. I run 7.5 with no fans no problem in my 2wd Cougar SV.

On another note, has anyone run the SP speedos with non sensor motors? Is there a setting change to make with the LCD? Or just disconnect the sensor cable? I know if I was on the track, and there was a cable failure, I would see a output difference. I dont know for sure what to do.:tire:

Originally Posted by apriliamille (Post 9528455)

hi,
i ordered a 2.1 pro stock esc, a 17.5 mmm and the lcd programmer
returning to the rc car hobby after 7 year break from it and have never used brushless in a rc car.

i see all the posts about upgrade software to the 323 stock
i have vista 32 bit and 64 bit o.s. in my pc. will the upgrade software work with
my vista computers? or do i have to upgrade to 7?

thanks

mike

Originally Posted by Solara (Post 9528907)

What is VISTA...? :eek:

Just kidding........it will work on 32bit. But honestly...XP and Win7 is a way better choice.

Originally Posted by apriliamille (Post 9531779)

for programming the esc?

Originally Posted by dug44 (Post 9532835)

Hello, bought a Speed Passion 8.5t,ultra sportsman version 2.0 from a reputable guy at my track. It was still factory sealed, and never been messed with. I put it in my buggy, double checked all my solder joints, and connections. Turned remote on, then car. Gave it some throttle, and poof. Smoke!
Went on to the speedpassion web-site, found the 888 number, called. I get a repeated message to hit 0 to continue. I hit 0, and it replays again to hit 0 to continue. All I want to do is send it in to get fixed. Not lookig for a hand-out in any means..... If you wouldn't mind, could you let me know what i have to do? Thanks Doug

Originally Posted by apriliamille (Post 9531779)

for programming the esc?

Originally Posted by Solara (Post 9532960)

I have contacted the office about your case...the phone is working, but for some reason when you called, it didn't get to the office probably because it is on hold for more then 2 calls inline...please call 1-888-928-1328 again. I have tried it and the phone is working.

Originally Posted by cougarcruisin (Post 9533802)

I ordered the Speed Passion silver arrow v2.0 2200 motor combo on amainhobbies.com this week.

I plan on trying it out in my hyper 9e. How well are these holding up in 1/8 buggy and what gearing have you guys been doing? So far i've read many of the pages here, but no one mentioned about putting them in the hyper9e.

Originally Posted by apriliamille (Post 9535054)

ok thanks all for the input and link to video.
hopefully it will work with my vista. gonna suck if i have to pay for windows 7 upgrade or a new laptop just to update an esc