|
What is a good starting setup for the VTX10R and a Viper 13.5 on a indoor clay low/med bite track, lots of tight turns, and two sweepers. Will be using a Losi 22.
Thanks! |
Originally Posted by SaladFork
(Post 9860360)
No :lol:. I don't have an exact price but it will NOT be 150 bucks.
This is the quote from their customer service "As for the price of VX4 Copperhead system, it will be $149.99 for the VX4R combo and $134.99 for the VX4 combo." |
Originally Posted by jurquhart
(Post 9867492)
I emailed the customer service to find a good starting point for my Losi 4x4 and to find out about price.
This is the quote from their customer service "As for the price of VX4 Copperhead system, it will be $149.99 for the VX4R combo and $134.99 for the VX4 combo." |
Originally Posted by tkge
(Post 9864605)
What is a good starting setup for the VTX10R and a Viper 13.5 on a indoor clay low/med bite track, lots of tight turns, and two sweepers. Will be using a Losi 22.
Thanks! Start with the 13.5 profile on the esc and tune from there as needed. We used that at a trophy race in NJ and our driver with a 13.5 was pulling cars with a 8.5 down the straights. Nick |
Thanks Nick!
|
Originally Posted by Littlejohn Dsgn
(Post 9867751)
I believe Salad was saying the sensored version will not be $150
|
went racing last night with my viper powered sc truck,
MUST SEE THE LAST MINUTE OF VIDEO.
|
|||||
I'm having trouble with the push button switch on my 10R speed control. It turns on ok, but after a run, it won't respond at all to pressing the button - it won't go to tune or shut off. I have to disconnect the battery.
When I turn it back on it the button will work again, but not after 5-10 minutes or runtime. Any ideas? The switch looks like its integral to the design so it doesn't look like I can even replace it. It's less than a month old. |
Originally Posted by bring it on
(Post 9872650)
went racing last night with my viper powered sc truck,
MUST SEE THE LAST MINUTE OF VIDEO. |
Originally Posted by rider313
(Post 9873025)
Awesome of you to wait when you made contact. Very classy. :cool:
|
Here is my Caster S10B viper powered 4wd buggy. VTX10R and 8.5 motor
|
|||||
Viper 13.5
I got to finally run my Viper 13.5 tonight and it was really smooth and had planty of power. Glad I switched over now and can't wait till my Viper VTX10R next week!!
|
Originally Posted by Grandturk
(Post 9872806)
I'm having trouble with the push button switch on my 10R speed control. It turns on ok, but after a run, it won't respond at all to pressing the button - it won't go to tune or shut off. I have to disconnect the battery.
When I turn it back on it the button will work again, but not after 5-10 minutes or runtime. Any ideas? The switch looks like its integral to the design so it doesn't look like I can even replace it. It's less than a month old. Weird, it doesn't shut off during the run at all, its just the switch function? The switch is its own circuit board. If you go to the website and fill out an warranty form, send it back and they will replace it pretty quickly. Where do you run in the NYC area, I bet we will cross paths at some tracks this winter. Nick |
Originally Posted by nikos2002
(Post 9875393)
Weird, it doesn't shut off during the run at all, its just the switch function? The switch is its own circuit board. If you go to the website and fill out an warranty form, send it back and they will replace it pretty quickly.
Where do you run in the NYC area, I bet we will cross paths at some tracks this winter. Nick |
Turk- sounds good, see you at the Trophy race next weekend.
|
| All times are GMT -7. It is currently 05:27 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.