R/C Tech Forums
Page 121 of 805
« First
21
71
111
119
120
121
122
123
131
171
221
621
Last »
Show 40 post(s) from this thread on one page

R/C Tech Forums (https://www.rctech.net/forum/)
-   Radio and Electronics (https://www.rctech.net/forum/radio-electronics-137/)
-   -   Viper RC - (https://www.rctech.net/forum/radio-electronics/455152-viper-rc.html)

mini-dub 06-08-2011 07:05 PM
Yes that was an early generation prototype. The VSE motors are dialed :tire:

idbdoug 06-08-2011 07:09 PM
Originally Posted by nikos2002 (Post 9228848)
Sounds good. If plans hold, I will see you down there. Viper is one of the Series sponsors - I went to RCE in MA, going to Trackside next weekend for round 2.

Being an on-road guys as well, you would like the smoothness of our system, but you still have all the power you need!!! Think about it.

Nick
What's the status of 17.5 1-cell Viper motor??? Would like to try 1 on Mike's Hobbyshop's Carpet track. Bring one to Dallas for the Short Course Showdown
idbdoug

Dlewis4 06-08-2011 07:10 PM
Originally Posted by mini-dub (Post 9229329)
Yes that was an early generation prototype. The VSE motors are dialed :tire:
Yes... very much so.

ShtLuck 06-08-2011 07:13 PM
sorry for the confusion.... ;)

i had no clue.
on a side note i would like to try to get setup with a 3s 550 can setup for my eco. i am trying to go light weight.:D
oh yeah derrick call me.

Cult Racing 06-09-2011 07:35 PM
Idk whats going on, but the 10r that was in my ae4x4 just stopped working on me now. I was running it up and down my street and then all the sudden turned off. So I was like maybe the motor or esc is hot and held my hand on it for about 3sec each. So i knew that wasnt the problem and then put a new battery in and still wont turn back on.

Dlewis4 06-09-2011 07:43 PM
Originally Posted by Cult Racing (Post 9234244)
Idk whats going on, but the 10r that was in my ae4x4 just stopped working on me now. I was running it up and down my street and then all the sudden turned off. So I was like maybe the motor or esc is hot and held my hand on it for about 3sec each. So i knew that wasnt the problem and then put a new battery in and still wont turn back on.
Have you contacted Weylin (Mini-dub)

Cult Racing 06-09-2011 07:44 PM
Originally Posted by Dlewis4 (Post 9234278)
Have you contacted Weylin (Mini-dub)
No, it just happened like 15min ago, but i will pm him.

SC_RAGE 06-09-2011 07:51 PM
hey cult give me the full rundown of what went on.

Cult Racing 06-09-2011 07:55 PM
Originally Posted by SC_RAGE (Post 9234318)
hey cult give me the full rundown of what went on.
I was running it up and down my street and then all the sudden turned off. So I was like maybe the motor or esc is hot and held my hand on it for about 3sec each. So i knew that wasnt the problem and then i dropped my truck little lower then my waist level and then hit the gas on the remote and all the sudden worked again for a split second and then wouldnt work again. So should i go to the hobby shop tomorrow and get it all resoldered and see if thats the problem? Is it because i run bullets instead of the straight wire from motor to esc?

smokinu 06-09-2011 08:02 PM
Originally Posted by Cult Racing (Post 9234329)
I was running it up and down my street and then all the sudden turned off. So I was like maybe the motor or esc is hot and held my hand on it for about 3sec each. So i knew that wasnt the problem and then i dropped my truck little lower then my waist level and then hit the gas on the remote and all the sudden worked again for a split second and then wouldnt work again. So should i go to the hobby shop tomorrow and get it all resoldered and see if thats the problem? Is it because i run bullets instead of the straight wire from motor to esc?
do the lights still work on the speedo?

what lights are flasing or glowing?

it could be a number of things but i would check for a cold solder joint first.

Cult Racing 06-09-2011 08:06 PM
Originally Posted by smokinu (Post 9234358)
do the lights still work on the speedo?

what lights are flasing or glowing?

it could be a number of things but i would check for a cold solder joint first.
well I just checked all the bullets and all the sudden one of the female bullets came right off, so im gonna go to the hobby shop and get it resoldered and see if that was the problem.

But when it was actually working, the green was glowing and when i hit the gas it would go red and flash.

smokinu 06-09-2011 08:31 PM
Originally Posted by Cult Racing (Post 9234380)
well I just checked all the bullets and all the sudden one of the female bullets came right off, so im gonna go to the hobby shop and get it resoldered and see if that was the problem.

But when it was actually working, the green was glowing and when i hit the gas it would go red and flash.
led's sound like normal operation.

i would have all the joints rechecked with a nice hot iron. and make sure its someone else using the iron. i hardly trust anyone soldering my gear unless its my sponsor rcrd LOL

Cult Racing 06-09-2011 09:54 PM
Originally Posted by smokinu (Post 9234477)
led's sound like normal operation.

i would have all the joints rechecked with a nice hot iron. and make sure its someone else using the iron. i hardly trust anyone soldering my gear unless its my sponsor rcrd LOL
lol i suck at soldering, so i go to one of the people i know who does all my stuff now.

SC_RAGE 06-09-2011 10:06 PM
Originally Posted by Cult Racing (Post 9234781)
lol i suck at soldering, so i go to one of the people i know who does all my stuff now.
http://www.youtube.com/watch?v=eU4t0Yko9Uk

This might help you.

Cult Racing 06-09-2011 10:26 PM
Originally Posted by SC_RAGE (Post 9234828)
sweet gonna have to buy a soldering station now.


All times are GMT -7. It is currently 11:50 PM.
Page 121 of 805
« First
21
71
111
119
120
121
122
123
131
171
221
621
Last »
Show 40 post(s) from this thread on one page

Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.