STS engines
09-09-2005, 04:09 PM
#1966
Originally Posted by dino.tw
GOGOGO~~~Go to buy your 1/8. Can't wait to beat your 1/8. 
09-09-2005, 04:24 PM
#1967
Originally Posted by jeffreylin
It's 7am in Taiwan...you must be dreaming.
check it out!
http://www.rctech.net/forum/showthre...3&page=8&pp=30
I said "where is your evolva?" on 07-14-2004
And it is 9-10-2005 I ask you AGAIN "where is your evolva?"
Sometime it is so fun to read old posts....
09-09-2005, 04:37 PM
#1968
Originally Posted by dino.tw
Jeff,
check it out!
http://www.rctech.net/forum/showthre...3&page=8&pp=30
I said "where is your evolva?" on 07-14-2004
And it is 9-10-2005 I ask you AGAIN "where is your evolva?"
Sometime it is so fun to read old posts....
check it out!
http://www.rctech.net/forum/showthre...3&page=8&pp=30
I said "where is your evolva?" on 07-14-2004
And it is 9-10-2005 I ask you AGAIN "where is your evolva?"
Sometime it is so fun to read old posts....
09-09-2005, 04:42 PM
#1969
Originally Posted by jeffreylin
Geez, it's taken me a year just to save enough for the engine! Chassis will probably take another year...
09-09-2005, 04:49 PM
#1970
Originally Posted by dino.tw
You must be kidding. That's ok! I have one Picco RS600 and another BMT chassis. If you want,I can give you one. It fits to your age.
09-09-2005, 05:03 PM
#1971
Originally Posted by jeffreylin
Picco?!?! What about STS!!!!
09-09-2005, 05:12 PM
#1972
Originally Posted by dino.tw
Left side is Picco RS600;right side is BMT. You can choice one,no kidding.
09-09-2005, 05:16 PM
#1973
dino's offering you a car and still with the insults 
dino if your givin your cars away can I have the one in the background then
dino if your givin your cars away can I have the one in the background then
09-09-2005, 05:18 PM
#1974
Originally Posted by jeffreylin
Goodness Dino you've been in RC for a long time why are you still so slow?
Yes,I'm slow but...I can finish every final without any trouble. You want me tell you how to make it?
09-09-2005, 05:24 PM
#1975
Originally Posted by Hesky
dino if your givin your cars away can I have the one in the background then
09-09-2005, 05:38 PM
#1976
sounds more like rejection to me 
maybe you could setup some sort of rc adoption agency, sounds like you have a few to many ex racers.
saying that I've gotta stop collecting all my old decaying rc cars and give them to my nephew or something.
maybe you could setup some sort of rc adoption agency, sounds like you have a few to many ex racers. saying that I've gotta stop collecting all my old decaying rc cars and give them to my nephew or something.
09-13-2005, 01:46 AM
#1977
Tech Apprentice
Hi guys,
Just purchased a d3r from mushroom. Anyway i read a few pages back in this thread that u need to clean or sand the piston etc (CORRECT ME PLS). Could you guys tell me what I have to do to the inside of the engine?
Thanks
Tiger
Just purchased a d3r from mushroom. Anyway i read a few pages back in this thread that u need to clean or sand the piston etc (CORRECT ME PLS). Could you guys tell me what I have to do to the inside of the engine?
Thanks
Tiger
09-13-2005, 02:21 AM
#1978
Tech Regular
huh sand the piston? thats new to me....
anyway, its always best with any engine, to open the backplate and pour some fuel thru it to get out any metal particles...
anyway, its always best with any engine, to open the backplate and pour some fuel thru it to get out any metal particles...
09-13-2005, 03:27 AM
#1979
Tech Master
Umm no, dont go doing that to the piston. Id inspect the engine, then put it back togther.. Get a hair dryer and heat it hot as then give her a start 
09-13-2005, 05:06 AM
#1980
Originally Posted by tiger266
Hi guys,
Just purchased a d3r from mushroom. Anyway i read a few pages back in this thread that u need to clean or sand the piston etc (CORRECT ME PLS). Could you guys tell me what I have to do to the inside of the engine?
Thanks
Tiger
Just purchased a d3r from mushroom. Anyway i read a few pages back in this thread that u need to clean or sand the piston etc (CORRECT ME PLS). Could you guys tell me what I have to do to the inside of the engine?
Thanks
Tiger
I think you are referring to a few post back where solutions were being discussed to help reduce the pinch (tightness of engine at tdc) via using metal polish. its not ideal, more like a desperate measure.