352LikesNOVAROSSI Engine thread....
04-11-2013 | 11:43 AM
#5298
Hey guys,
I have an FMS that I've babied for a couple of years (had Ray tighten it up last fall). Use it in 1/8th Late Model.
Any ideas on a replacement piston ? (sleeve is ok). part numbers and good prices? Thanks in advance...
I have an FMS that I've babied for a couple of years (had Ray tighten it up last fall). Use it in 1/8th Late Model.
Any ideas on a replacement piston ? (sleeve is ok). part numbers and good prices? Thanks in advance...
04-11-2013 | 11:53 AM
#5299
for part numbers talk to Monty he should be able to help you
04-11-2013 | 03:29 PM
#5301
if all is good Ray has resized MANY p/s sets more than once
04-11-2013 | 07:36 PM
#5302
Completely gutted. Love this motor....
04-12-2013 | 02:04 AM
#5303
I just changed out the rod on my roma took me a few clips to get it done right
04-12-2013 | 05:06 AM
#5304
I was sitting at my workbench after replacing the rod/clips etc. slotted the piston back into the case and was getting ready to slide the sleeve back in when the piston dropped out, through my legs and onto the floor. I was sitting in one of those rolling desk chairs with five sets of wheels. I pushed myself away from the desk to find it, and the wheels rolled right over the piston (with my fat 220lbs of weight on it)....Pic attached...sob sob
Will this piston work?
Last edited by tobamiester; 04-12-2013 at 06:22 AM.
04-12-2013 | 09:10 AM
#5305
ooh no
Oh it was worse than that
I was sitting at my workbench after replacing the rod/clips etc. slotted the piston back into the case and was getting ready to slide the sleeve back in when the piston dropped out, through my legs and onto the floor. I was sitting in one of those rolling desk chairs with five sets of wheels. I pushed myself away from the desk to find it, and the wheels rolled right over the piston (with my fat 220lbs of weight on it)....Pic attached...sob sob
Will this piston work?
I was sitting at my workbench after replacing the rod/clips etc. slotted the piston back into the case and was getting ready to slide the sleeve back in when the piston dropped out, through my legs and onto the floor. I was sitting in one of those rolling desk chairs with five sets of wheels. I pushed myself away from the desk to find it, and the wheels rolled right over the piston (with my fat 220lbs of weight on it)....Pic attached...sob sob
Will this piston work?
04-12-2013 | 09:46 AM
#5307
04-13-2013 | 06:29 AM
#5308
Oh it was worse than that
I was sitting at my workbench after replacing the rod/clips etc. slotted the piston back into the case and was getting ready to slide the sleeve back in when the piston dropped out, through my legs and onto the floor. I was sitting in one of those rolling desk chairs with five sets of wheels. I pushed myself away from the desk to find it, and the wheels rolled right over the piston (with my fat 220lbs of weight on it)....Pic attached...sob sob
Will this piston work?
I was sitting at my workbench after replacing the rod/clips etc. slotted the piston back into the case and was getting ready to slide the sleeve back in when the piston dropped out, through my legs and onto the floor. I was sitting in one of those rolling desk chairs with five sets of wheels. I pushed myself away from the desk to find it, and the wheels rolled right over the piston (with my fat 220lbs of weight on it)....Pic attached...sob sob
Will this piston work?
The top part of the piston it ran rough after that lesson Learnt always put something soft down lol
04-13-2013 | 06:41 AM
#5309
