Kyosho v-one rrr
#1531
Re: ROLL CENTER CLIPS
Originally posted by jwf_frani
A: set on the lowest postition in the rear will lower your roll center.
B: set on the lowest postition in the rear is the next step up
B: on the reversed position would be next higher
A: on the high postion for the rear would be the highest setting.
(front)
the higher the inner hinge pin is the lower the roll center
A: set on the lowest postition in the rear will lower your roll center.
B: set on the lowest postition in the rear is the next step up
B: on the reversed position would be next higher
A: on the high postion for the rear would be the highest setting.
(front)
the higher the inner hinge pin is the lower the roll center
#1532
Re: Re: ROLL CENTER CLIPS
Originally posted by dameetz
How about the spacer on top of rear upright? If I add the spacer will it make the rear roll center lower?
How about the spacer on top of rear upright? If I add the spacer will it make the rear roll center lower?
#1533
RC MOdel HK
Hi guys hows the RC Model right HK now, are they operational or still on vacation? i want to know coz i need to order some tires... tnx.
#1534
Tech Adept
v one rrr wc
Does that kit come with the kyosho foams (rim pattern) shown in the press release or regular grp 35 degree foams? Thanks.
#1535
grp37's 26mm front 30mm rear comes with wc, they are spoked rims, but not the same as the regular type spoked ones
#1536
has anybody here using a team magic alpha starter box? will it work w/ the v one rrr?
#1537
Tech Addict
iTrader: (4)
rrr wc aditional parts
I am in the process of buying the WC edition. Without having to go through the whole thread, can anyone suggest what upgrades I should still get? I am ordering spare belts, and front suspension arms off hand. I am placing the order oversees, so I would like to make 1 big order.
Thanks in advance.
Thanks in advance.
#1538
Tech Addict
iTrader: (11)
Option parts for RRR!!!!
Here are a few option parts to add!
1. Aluminum front sway bar
2. Aluminum center deck brace (2 pieces)
3. skyline 4mm rear shock tower
4. extra 55T and 56T spur gears
5. extra 16T and 17T pinions; get 1 15T pinion
6. front knuckles
7. pulley set
8. joint 19 outdrives
9. white shock diaphrams
10. rear uprights
11. small shock parts
12. extra front and rear bulkheads
13. skyline pipe support
14. aluminum center main shaft pulley for rear diff
15. front oneway and rear diff aluminum access covers
16. rear set diff gears
17. all sets of springs to go all around
18. Extra fuel tanks
19. replacement bearings
20. extra clutch bells for other gears
21. Venom 1200 maH battery packs (2).
22. extra pillow balls to replace a bent one
Hope this helps.
I went whacky on you!
1. Aluminum front sway bar
2. Aluminum center deck brace (2 pieces)
3. skyline 4mm rear shock tower
4. extra 55T and 56T spur gears
5. extra 16T and 17T pinions; get 1 15T pinion
6. front knuckles
7. pulley set
8. joint 19 outdrives
9. white shock diaphrams
10. rear uprights
11. small shock parts
12. extra front and rear bulkheads
13. skyline pipe support
14. aluminum center main shaft pulley for rear diff
15. front oneway and rear diff aluminum access covers
16. rear set diff gears
17. all sets of springs to go all around
18. Extra fuel tanks
19. replacement bearings
20. extra clutch bells for other gears
21. Venom 1200 maH battery packs (2).
22. extra pillow balls to replace a bent one
Hope this helps.
I went whacky on you!
#1539
You could also try one of the 3-racing lightweight clutch bells....by my calculations they weigh about 20% less than the stock Kyosho bell so it`ll be interesting to see what affect they have on performance........I havent had the chance to try mine out yet
Cheers
Cheers
#1540
Tech Addict
iTrader: (4)
Re: Option parts for RRR!!!!
Originally posted by bighurt98
Here are a few option parts to add!
1. Aluminum front sway bar
2. Aluminum center deck brace (2 pieces) cou
3. skyline 4mm rear shock tower
4. extra 55T and 56T spur gears
5. extra 16T and 17T pinions; get 1 15T pinion
6. front knuckles-- ARE THERE DIFFERENT ONES? -1, -2
7. pulley set
8. joint 19 outdrives --WHAT ARE THESE
9. white shock diaphrams fOR THE SHOCKS? mAYBE I CAN HOLD OFF ON THESE
10. rear uprights COULDN'T FIND PART NUMBERS
11. small shock parts WILL HOLD FOR NOW
12. extra front and rear bulkheads
13. skyline pipe support
14. aluminum center main shaft pulley for rear diff
15. front oneway and rear diff aluminum access covers-- PLEASE EXPLAIN THE ADVANTAGE, COULDN'T FIND THEM EITHER
16. rear set diff gears
17. all sets of springs to go all around
18. Extra fuel tanks
19. replacement bearings IS THE ONLY PLACE WHERE THE CAR USED BUSHINGS IN THE KNUCKLES?
20. extra clutch bells for other gears
21. Venom 1200 maH battery packs (2). dOES THE CAR USE THE STANDARD FLAT PACKS
22. extra pillow balls to replace a bent one
Hope this helps.
I went whacky on you!
Here are a few option parts to add!
1. Aluminum front sway bar
2. Aluminum center deck brace (2 pieces) cou
3. skyline 4mm rear shock tower
4. extra 55T and 56T spur gears
5. extra 16T and 17T pinions; get 1 15T pinion
6. front knuckles-- ARE THERE DIFFERENT ONES? -1, -2
7. pulley set
8. joint 19 outdrives --WHAT ARE THESE
9. white shock diaphrams fOR THE SHOCKS? mAYBE I CAN HOLD OFF ON THESE
10. rear uprights COULDN'T FIND PART NUMBERS
11. small shock parts WILL HOLD FOR NOW
12. extra front and rear bulkheads
13. skyline pipe support
14. aluminum center main shaft pulley for rear diff
15. front oneway and rear diff aluminum access covers-- PLEASE EXPLAIN THE ADVANTAGE, COULDN'T FIND THEM EITHER
16. rear set diff gears
17. all sets of springs to go all around
18. Extra fuel tanks
19. replacement bearings IS THE ONLY PLACE WHERE THE CAR USED BUSHINGS IN THE KNUCKLES?
20. extra clutch bells for other gears
21. Venom 1200 maH battery packs (2). dOES THE CAR USE THE STANDARD FLAT PACKS
22. extra pillow balls to replace a bent one
Hope this helps.
I went whacky on you!
Thanks for the reply. I made some comments in Caps.. I appreciate the help. My ntc3 is so much easier to deal with
#1541
Originally posted by AndyT ©
You could also try one of the 3-racing lightweight clutch bells....by my calculations they weigh about 20% less than the stock Kyosho bell so it`ll be interesting to see what affect they have on performance........I havent had the chance to try mine out yet
Cheers
You could also try one of the 3-racing lightweight clutch bells....by my calculations they weigh about 20% less than the stock Kyosho bell so it`ll be interesting to see what affect they have on performance........I havent had the chance to try mine out yet
Cheers
#1542
Originally posted by rowveg36
has anybody here using a team magic alpha starter box? will it work w/ the v one rrr?
has anybody here using a team magic alpha starter box? will it work w/ the v one rrr?
#1543
I`m going to svitch from a MTX-3 to a V1rrr.
Is there anything i should keep from my Mugen.... i have a ton of new spares from it, pinions cluchbells etc.... but i dont know if there is anything that fits the v1rrr
Is there anything i should keep from my Mugen.... i have a ton of new spares from it, pinions cluchbells etc.... but i dont know if there is anything that fits the v1rrr
#1544
what i am realy intrested in is if the pinions, clutch bell work.... also is the Kawahara aluminium servoaver (ackerman) for the Mtx-3 a direct fit for the V1rrr....
#1545
Originally posted by Ec1
I`m going to svitch from a MTX-3 to a V1rrr.
I`m going to svitch from a MTX-3 to a V1rrr.
Why not get the RRR, build it and test it first before making the complete swtich? Then you'll know if you like it or not and if those Mugen parts you're asking fits on the RRR... Sure and safe way of knowing.