Serpent 710
#7336
Originally posted by cyba888
10-11 months...I hope its because of the 705 problems that people are talking about. If the 710 proves to be a great car all around then it should stay around for some time.
10-11 months...I hope its because of the 705 problems that people are talking about. If the 710 proves to be a great car all around then it should stay around for some time.
#7338
Re: Re: Re: Question for GlennCauley?or Julius or "InitialD"
Originally posted by Marcos.S710
thanks hopefully Julius will read these posting later today and he can comment on it , or InitialD
thanks hopefully Julius will read these posting later today and he can comment on it , or InitialD
#7339
Tech Regular
iTrader: (3)
Re: Re: Re: Re: Question for GlennCauley?or Julius or "InitialD"
Originally posted by Julius
The TP04 was a pipe good for bottom end. The TP05 was better in top end. The TP06 combines both. Itīs good both low and top.
The TP04 was a pipe good for bottom end. The TP05 was better in top end. The TP06 combines both. Itīs good both low and top.
Hope it doesn't have a big black hole in between where mid-range is supposed to be.
Glenn Cauley
Ottawa, Canada
#7340
New Nova Mega conical for .12
New Nova Mega conical for .12 part nr. 2175
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
#7341
Re: New Nova Mega conical for .12
Originally posted by border r/c
New Nova Mega conical for .12 part nr. 2175
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
New Nova Mega conical for .12 part nr. 2175
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
#7342
Originally posted by cyba888
Why is your engine taking so long to get delivered? Did you pay for sea freight?
Why is your engine taking so long to get delivered? Did you pay for sea freight?
#7343
Re: Re: New Nova Mega conical for .12
Originally posted by markp27
Have you guys got the NovaMega SX12 SS 3P - Turbo (#2106) in stock?
Have you guys got the NovaMega SX12 SS 3P - Turbo (#2106) in stock?
#7344
Tech Regular
iTrader: (3)
Re: Re: Re: New Nova Mega conical for .12
Originally posted by Schrijver99
Why don't you wait for the MS edition with the MCP P/S?
Why don't you wait for the MS edition with the MCP P/S?
Rob Kuijper responded back to me that they are a little bit better success with the newer SX12 SS 3P (#2106). So that is what I got. With the TP06 1-pc pipe (#2170) hopefully will be a good combination.
Just some food for thought...
Glenn Cauley
Ottawa, Canada
#7345
Tech Regular
iTrader: (3)
Re: New Nova Mega conical for .12
Originally posted by border r/c
New Nova Mega conical for .12 part nr. 2175
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
New Nova Mega conical for .12 part nr. 2175
this the manifold were there was talked about now in stock
http://shop.the-border.nl/customer/p...806&cat=&page=
Why would I want to use this?
Will the stock header on the 2170 pipe (TP06) not be good?
Glenn Cauley
Ottawa, Canada
#7346
Tech Rookie
Conical Header for .12
Hi Glenn,
good to see you posting !!
My experience with a conical header on a .12 is that the bottom end is not all that good but middle range and top speed is a little better, please note that clutch and carb setting gets more critical !
I would still go for the 2170 pipe system for the short to medium tracks, and give that conical header a try on longer tracks.
Note that the picture on the Border site is from a .21 header
no official pic's yet !?
good to see you posting !!
My experience with a conical header on a .12 is that the bottom end is not all that good but middle range and top speed is a little better, please note that clutch and carb setting gets more critical !
I would still go for the 2170 pipe system for the short to medium tracks, and give that conical header a try on longer tracks.
Note that the picture on the Border site is from a .21 header
no official pic's yet !?
#7347
Re: Re: Re: Re: New Nova Mega conical for .12
Originally posted by GlennCauley
When I was trying to select the engine for my S710, I asked Serpent what would be better... the SX12 MCP or the newer SX12 SS 3P (#2106)
Rob Kuijper responded back to me that they are a little bit better success with the newer SX12 SS 3P (#2106). So that is what I got. With the TP06 1-pc pipe (#2170) hopefully will be a good combination.
Just some food for thought...
Glenn Cauley
Ottawa, Canada
When I was trying to select the engine for my S710, I asked Serpent what would be better... the SX12 MCP or the newer SX12 SS 3P (#2106)
Rob Kuijper responded back to me that they are a little bit better success with the newer SX12 SS 3P (#2106). So that is what I got. With the TP06 1-pc pipe (#2170) hopefully will be a good combination.
Just some food for thought...
Glenn Cauley
Ottawa, Canada
Also i'm sorry to tell but Rob Kuijper doesn't work/race anymore for Serpent (he's gone over to work for Kyosho)
#7348
Re: Conical Header for .12
Originally posted by RobK1
Hi Glenn,
good to see you posting !!
Note that the picture on the Border site is from a .21 header
no official pic's yet !?
Hi Glenn,
good to see you posting !!
Note that the picture on the Border site is from a .21 header
no official pic's yet !?
#7349
Tech Rookie
Hi Bas,
Thanx for the kind words,
i hope you have better luck in the upcoming races
C-Ya
Rob
i hope you have better luck in the upcoming races
C-Ya
Rob
#7350
Tech Regular
iTrader: (3)
Re: Re: Re: Re: Re: New Nova Mega conical for .12
Originally posted by Schrijver99
I'm Talking about the new SX12 SS 3P MCP MS (#2106MS) which is coming soon
Also i'm sorry to tell but Rob Kuijper doesn't work/race anymore for Serpent (he's gone over to work for Kyosho)
I'm Talking about the new SX12 SS 3P MCP MS (#2106MS) which is coming soon
Also i'm sorry to tell but Rob Kuijper doesn't work/race anymore for Serpent (he's gone over to work for Kyosho)
When is this new engine coming out?
<sigh>... trying to keep up with these engines is darn near impossible...
I knew about Rob's leaving Serpent a while ago.
Rob, you are missed...
But glad to see you haven't disappeared forever!
Glenn Cauley
Ottawa, Canada