|
Originally Posted by Goingfast
(Post 4542671)
Who got the best deal on line( NT1 parts)?Thanks
|
Originally Posted by TomB
(Post 4535403)
just remember to re check your engine temp and tune with the new heatsink, as it may affect the tune slightly either make it run a bit cooler or hotter, depends on the place you race at. also there is less amterial so it may run a bit hotter, who knows, just double check though.
did you use it already? what did you experience? |
I've had great luck with Nexus and Ashford Hobbies.
|
Originally Posted by TeamCarnage
(Post 4544769)
I've had great luck with Nexus and Ashford Hobbies.
|
tyre wear
will softening my clutch or running a softer spring help me with my tyre wear?
|
Originally Posted by grub
(Post 4546968)
will softening my clutch or running a softer spring help me with my tyre wear?
no |
Originally Posted by Ramiel
(Post 4544597)
no probs.
did you use it already? what did you experience? |
Originally Posted by grub
(Post 4546968)
will softening my clutch or running a softer spring help me with my tyre wear?
|
Originally Posted by TomB
(Post 4547539)
not really i used it last club day but my engine was fired up for the first time in 2.5 months so it was out of tune. i'll know for sure in a few weeks time
|
Originally Posted by teamgp
(Post 4547681)
Explain the exact tire wear problem. All four tires wearing fast...rear tires only wearing fast...left or right side only wearing fast...etc. Also, what are the track conditions (smooth/bumpy, low/med/high grip, any traction compound) and the tire brand/shore rating that your using.
there no traction compound added the tracks has no/low traction bumpy has 6 left turns and 3 right and turns and runs counter clock wise |
Originally Posted by grub
(Post 4548930)
ok front tyre wear flate and even left rear side wear about 3mm over ten minutes right rear 6 mm over ten im using 37 and 40 shore kawaraha's all round ..
there no traction compound added the tracks has no/low traction bumpy has 6 left turns and 3 right and turns and runs counter clock wise :confused: If that so, I think you have to complain the track condition to track owner. It's very bad surface. Need recondition. |
Originally Posted by asw7576
(Post 4550468)
you lost 3mm on the right and 6mm on the left in 10 minutes ?
:confused: If that so, I think you have to complain the track condition to track owner. It's very bad surface. Need recondition. we only have 2 years on the lease so i will have to put up with the surface for now we run on an old netball court 1970 bitchimen the other car manafactors cars dont loose that much tyre i think its just me:mad: i cant spell by the way:lol: |
Originally Posted by grub
(Post 4550614)
yes it a bad bumpy car breaking surface but better than nothing
we only have 2 years on the lease so i will have to put up with the surface for now we run on an old netball court 1970 bitchimen the other car manafactors cars dont loose that much tyre i think its just me:mad: i cant spell by the way:lol: Resurface the track why didn't I think of that Grub!............... |
Originally Posted by grub
(Post 4550614)
we run on an old netball court 1970 bitchimen
the other car manafactors cars dont loose that much tyre i think its just me:mad: i cant spell by the way:lol: :D Well, I hope you can fix your tire problem. Sorry, I can't help..... I'm not a setup expert. |
Hey Guy’s
Just a quick question I have a NT1 ‘08’. The car is great to drive having heaps of fun with it only still learning how to drive it. I have put around 2ltr of fuel through it. But so far I have replaced the left hand side front diff bearing (941016) due to it melting the composite adjuster ball-bearing hub (332070) And last night at racing the front left hand side inner (941016) wheel bearing I found half way through the race the car was not right. We stopped the car and found that the left side wheel was not right we removed the wheel and found the composite steering block was starting to melt due to the bearing locking up. Is this a common thing with the NT!? Are the standard bearings out of the kit dry bearing or filled with oil? Can you get a set of bearings that are filled with grease? Or is it worthwhile to remove the bearing shield and fill with a light bearing grease. Yes I have seen ceramic bearing but they are a little expensive. Does Xray have a grease to suit the bearings in the NT1 kit? Do you guys have this problem with the bearing? How do you guy’s maintain your bearings?Or do you guys have any ideas? Thank you |
| All times are GMT -7. It is currently 03:25 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.