Kyosho V-ONE RRR Evo
12-09-2006, 06:06 AM
#781
Originally Posted by doki_doki
i could see the slot. is the pulley aluminum? from the looks of it, it looks like it is made of plastic material. i might be wrong 
there are a few additons that are on the EVO WCTE that I really like.
Im on the final stages of building it just finished the clutch & will go back to figure the best way on wiring it up will post some pics.
I must say the shocks are a definite upgrade different bladders,titanium shafts
12-09-2006, 10:13 PM
#782
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
Originally Posted by 710baby
the pulley is plastic the pulley shaft & spacer are aluminum
there are a few additons that are on the EVO WCTE that I really like.
Im on the final stages of building it just finished the clutch & will go back to figure the best way on wiring it up will post some pics.
I must say the shocks are a definite upgrade different bladders,titanium shafts
there are a few additons that are on the EVO WCTE that I really like.
Im on the final stages of building it just finished the clutch & will go back to figure the best way on wiring it up will post some pics.
I must say the shocks are a definite upgrade different bladders,titanium shafts
12-09-2006, 10:24 PM
#784
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
I was able to find time to install the kawahara side brace 
I really thick and adds support to resist chassis flex 
I really thick and adds support to resist chassis flex
12-09-2006, 10:26 PM
#786
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
I also installed the kawahara aluminum brake bracket Looks really nice and adds rigidity to the rear bulkheads...
Looks really nice and adds rigidity to the rear bulkheads...
12-09-2006, 10:31 PM
#787
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
I replaced the stock kyosho plastic brake lever with kyosho's aluminum brake lever With this upgrade, there is no more slop and I noticed a very consistent brake feel I had to take out some of my braking EPA after installing this upgrade
With this upgrade, there is no more slop and I noticed a very consistent brake feel I had to take out some of my braking EPA after installing this upgrade
12-09-2006, 10:36 PM
#789
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
Last but not the least, I installed the kawahara aluminum radio post What I noticed is that with this upgrade, it eliminates the use of the stock FRP belt tensioner that holds the bearing. Now, the bearing is directly attached to the aluminumn radio post and is much easier to adjust
What I noticed is that with this upgrade, it eliminates the use of the stock FRP belt tensioner that holds the bearing. Now, the bearing is directly attached to the aluminumn radio post and is much easier to adjust
12-09-2006, 10:49 PM
#791
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
Originally Posted by fritzD
doki,
awesome Upgrades!!!
awesome Upgrades!!!
12-10-2006, 10:38 AM
#792
Tech Master
iTrader: (3)
Join Date: Dec 2001
Location: Costa Del Sol, Marbella, Spain www.bradir.net
Posts: 1,456
Trader Rating: 3 (100%+)
mah ride
my vone RRR with my new nova plus 12-5ct and pipe
12-11-2006, 03:44 AM
#794
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
Originally Posted by ianhobbies
my vone RRR with my new nova plus 12-5ct and pipe
12-11-2006, 04:10 AM
#795
doki, what is the part number for the aluminum brake arm?