R/C Tech Forums - View Profile: Corners
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

Corners's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

Corners Corners is offline

Tech Adept

Last Activity: 04-11-2023 01:07 PM

About Me

  • Signature
    17.5 B6.4D, 21.5 B6D.3/1, NPRC Home Built, and a Stock Spec Slash.

    The Certainty Principal - "Only the person who doesn't fully understand the problem has complete certainty about the best solution and its consequences. Certainty is proportional to the square of Ignorance (C≈I˛)"

Statistics

Total Posts
General Information
  • Last Activity: 04-11-2023 01:07 PM
  • Join Date: 08-26-2012
  • Referrals: 0

Likes Received

16 Likes
  1. MonkeyCmonkeyDo liked post by Corners On thread : buggys go bye bye?
    Knoby tires are for loose dirt. Indoor clay will either be slicks or a very light tread.
    Liked On: 04-04-2023, 09:35 PM
    Posted On: 04-04-2023, 09:24 PM
  2. Jblack45 liked post by Corners On thread : Ceramic bearing question
    Yeah, dirty. Sometimes with stubborn ones, I’ll soak in the citrus degreaser, pull it out, spin it, soak it, spin it, soak it, spray it out with water, then immediately dry with an air compressor,...
    Liked On: 04-04-2023, 03:56 PM
    Posted On: 04-04-2023, 02:51 PM
  3. chili81 liked post by Corners On thread : Hard to find bearings or custom bushing/spacer to allow std bearing?
    Ask a friend with a 3D printer to print a few spacers. Most libraries have free 3D printers to use as well. Seems like a a ton of people have them these days, since a decent printer is like $200 or...
    Liked On: 02-15-2023, 12:44 PM
    Posted On: 02-14-2023, 06:09 PM
  4. MrLean liked post by Corners On thread : Team Associated B6.4 and B6.4d
    Open area is one variable, and the other is linear contact. That is, the circumference of the holes. The circumference is where the hole is touching the fluid setting up a boundary area. More contact...
    Liked On: 02-07-2023, 07:12 AM
    Posted On: 02-06-2023, 04:27 PM
  5. aracefan
    aracefan liked post by Corners On thread : Bit vs driver
    The main issue is the inconsistency and the “gamble” you take going another direction. MIP is always tops in quality of materials and accuracy in dimensions. You might find another that works, but...
    Liked On: 01-29-2023, 05:33 PM
    Posted On: 01-29-2023, 08:57 AM
  6. Andy Koback liked post by Corners On thread : Help, need advice for swollen Lipos
    12V light bulb outside and leave it for hours. Then put it in a bucket of salt water for a few days. Then toss it in the trash (or take to a recycler if you have one).
    Liked On: 01-08-2023, 05:32 PM
    Posted On: 01-08-2023, 07:54 AM
  7. Bud liked post by Corners On thread : Help, need advice for swollen Lipos
    12V light bulb outside and leave it for hours. Then put it in a bucket of salt water for a few days. Then toss it in the trash (or take to a recycler if you have one).
    Liked On: 01-08-2023, 08:54 AM
    Posted On: 01-08-2023, 07:54 AM
  8. xen0ph0n liked post by Corners On thread : Blinky classes?
    You might check on the 21.5T class. Over the past couple years, the 21.5T class seems to be more of what "stock" class used to be, with a little lower speeds and usually rules requiring spec motors...
    Liked On: 01-03-2023, 12:53 PM
    Posted On: 01-03-2023, 12:44 PM
  9. mrreet2001
    mrreet2001 liked post by Corners On thread : JB Weld
    That car has a ball diff. Just crank the diff down tight so it doesn't backspin without some force. If that's not working, take the balls out of the diff, and put a rubber washer between the gear and...
    Liked On: 02-11-2022, 09:51 AM
    Posted On: 02-03-2022, 02:07 PM
  10. Eric Tomczyk liked post by Corners On thread : The resurgence of forums
    Yes, they are right now, but people are currently leaving Facebook looking for other outlets in the fallout from big tech censorship. Curious how this is going to play out.
    Liked On: 01-21-2021, 12:58 PM
    Posted On: 01-11-2021, 03:24 PM
  11. Eric Tomczyk liked post by Corners On thread : The resurgence of forums
    With big tech censorship on everyone’s minds these days, it appears that we are on the horizon of a resurgence of forums away from social media. I know a local car forum in our area had shut down...
    Liked On: 01-21-2021, 12:54 PM
    Posted On: 01-11-2021, 02:59 PM
  12. petersen114
    petersen114 liked post by Corners On thread : The resurgence of forums
    Yes, they are right now, but people are currently leaving Facebook looking for other outlets in the fallout from big tech censorship. Curious how this is going to play out.
    Liked On: 01-17-2021, 12:50 PM
    Posted On: 01-11-2021, 03:24 PM
  13. Raguvian liked post by Corners On thread : The resurgence of forums
    Yep. Elon posted this the other day. https://i.ibb.co/x51z4ML/B0674-CDA-32-E7-4-A36-B567-CC8758-F10-F83.jpg (https://ibb.co/Jkvrhzt) host photo (https://imgbb.com/)
    Liked On: 01-11-2021, 04:04 PM
    Posted On: 01-11-2021, 03:37 PM
  14. Antimullet liked post by Corners On thread : Budget priced pit light
    Bought this light per the recommendation. Great light. However, my wife may have stolen it from me.
    Liked On: 02-12-2018, 10:10 AM
    Posted On: 02-03-2018, 07:00 PM
  15. billdelong liked post by Corners On thread : Turned a Corner in Racing
    Not to derail this good topic, but for you personally, you have to respect the passing of the guard. There will be a time where your sons will beat you. And acknowledging it now will prepare you...
    Liked On: 01-30-2018, 08:26 AM
    Posted On: 01-30-2018, 07:37 AM
Page 1 of 2
1
2

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.