|
I will have to look for them.
|
Seidel rc doesn’t ship outside Germany:mad: |
Originally Posted by ShtLuck
(Post 15353758)
so i just ordered a 419x i will probably go xr at some point. I am running in USGT and coming from a TB EVO 7 that i struggled with the crazy amount of grip it made on CRC black carpet. Anything i need to do for black carpet or any band aids i need to know about during the build up? also what is a good starting point for the car on black carpet?
1. Less front toe out (around 1.5) 2. Springs (I use SMJ - 2.8 or 3.0 linear rear, 2.7-3 progressive front 3. One step harder front antirollbar 4. Soft (ball) central stiffener 5. Top Deck from WS If you use alu deck I would recommend to use thinner top deck (Vigor 1.6) Diff oil 6k up. Lately I use 8k some use 10k Dampers oil 450-500 Important: 1. Mill/sand topdeck near spur gear as the clearance is too small. While driving it will spur rubs against topdeck (I had this in 419X, WS and XR as well) 2. Use third bearing inside spur gear (pulleys). You have to buy this separately. It will save you pain with sloppy spur and shaft. In the end pulleys would have to be replaced as they wobble. It cannot be shimmed as the shims press against bearings making them too tight. Those are IMHO two obvious flaws in this model. |
Originally Posted by Macio4ever
(Post 15354637)
I would start with stock setup which is good starting point. I race with some minor changes:
1. Less front toe out (around 1.5) 2. Springs (I use SMJ - 2.8 or 3.0 linear rear, 2.7-3 progressive front 3. One step harder front antirollbar 4. Soft (ball) central stiffener 5. Top Deck from WS If you use alu deck I would recommend to use thinner top deck (Vigor 1.6) Diff oil 6k up. Lately I use 8k some use 10k Dampers oil 450-500 Important: 1. Mill/sand topdeck near spur gear as the clearance is too small. While driving it will spur rubs against topdeck (I had this in 419X, WS and XR as well) 2. Use third bearing inside spur gear (pulleys). You have to buy this separately. It will save you pain with sloppy spur and shaft. In the end pulleys would have to be replaced as they wobble. It cannot be shimmed as the shims press against bearings making them too tight. Those are IMHO two obvious flaws in this model. Thanks, Jose |
I used third bearing (3 or 4mm wide) inside one of the pulleys - red arrow shows where you should put your bearing. With three bearings shaft and pulleys have close to none play. When assembled I have just very, very tiny play (I think < 0,1mm) and spur spin freely for a couple of seconds. This tiny play is needed as spur and pinion will nicely mesh.
Bearings are standard size but different ones for X/XWS and XR (XR has thicker shaft). https://cimg2.ibsrv.net/gimg/www.rct...ff8b367347.jpg TRF419X Pulley and additional bearing |
Anyone know anything new for tamiya this time of the year.........new trf |
The TA07MS has just started to hit stores (That is a new TRF, a single belt 419XR). Also the 419XR has recently been released globally as a full kit. It will be a while before a new 419 but there will be one at some point I am sure :) |
Originally Posted by trf415msx
(Post 15356600)
Anyone know anything new for tamiya this time of the year.........new trf tamiya japan page new releases |
What is the effect of using F1 FR0.5/F0.5 FR1
|
Originally Posted by trf415msx
(Post 15356600)
Anyone know anything new for tamiya this time of the year.........new trf But probably great MS cars... |
Originally Posted by Airwave
(Post 15358890)
sorry but there won't be any new trf cars...
But probably great MS cars... There will infact be more TRF cars and MS cars.. this is from sources in Tamiya.. so please don’t spread unverified rumours |
Which front uprights comes with the original 419x kit?
Its it the 418 C Carbon #54568? |
Originally Posted by airbiscuit
(Post 15359774)
Which front uprights comes with the original 419x kit?
Its it the 418 C Carbon #54568? |
Originally Posted by Tom1977
(Post 15354080)
For carpet i recommend the 419X-WS aluminium lower deck and the 1.7mm X-WS upper deck. But both hard to get...
https://cimg8.ibsrv.net/gimg/www.rct...3a621cc9aa.jpg https://cimg4.ibsrv.net/gimg/www.rct...544618108d.jpg thank you |
Looking for. 419x aluminum chassis
I’m also looking for a 419x aluminum chassis. Please pm me if you have one for sale |
| All times are GMT -7. It is currently 11:00 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.