T.O.P. Racing "Photon" 1/10 EP Touring Car
#3557
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
my diff bolt was protruding well past my diff nut.. nearly an eigth of an inch.. using less beveled washers will only cause the nut to retreat.. i guess i could have used a thicker collar on the thrust side. funny even the cad drawing shows the tip of the bolt protruding.. the end of mine was shinny where it had been rubbing.. i see the blades are "out of stock". i must not be alone..
QUOTE]
Ron is correct, either install the shorter dog bones or add 1.5mm to the rear will solve this.
#3558
Tech Elite
iTrader: (12)
[QUOTE=Nova F1 Racer;6980425]
I've got some v2 and v3 bones in steel and aluminum. Which are the short ones? From which points can the installed ones be measured? Thanks for all the good info guys.
If your still running the original 45mm dog bones and trying to run more then 1.5* of rear camber that's how there breaking. If you go to the 44.5mm pick up the CVD collars at the same time. They really help free up the dog bones.
QUOTE]
Ron is correct, either install the shorter dog bones or add 1.5mm to the rear will solve this.
QUOTE]
Ron is correct, either install the shorter dog bones or add 1.5mm to the rear will solve this.
#3559
Tech Elite
iTrader: (102)
Join Date: Dec 2004
Location: Far away from Covid19 but close to 20
Posts: 4,129
Trader Rating: 102 (100%+)
Shave and Cut
Is it me or does it seem like Schreff went down to the 'Birds
with a new hair dew (cut) and shaved....
seems like someone knew he was going to be taking pics with the girls!!!!
20 oz steak is due to the winner.....lot'so Oniooanss...
Congrats to the Top Team ...well deserved
Congrats to the Goat...time for a TOP shirt. wealth of knowledge
with a new hair dew (cut) and shaved....
seems like someone knew he was going to be taking pics with the girls!!!!
20 oz steak is due to the winner.....lot'so Oniooanss...
Congrats to the Top Team ...well deserved
Congrats to the Goat...time for a TOP shirt. wealth of knowledge
#3560
Tech Adept
hello
which is the difference in using this parts camber link plate 1.25 mm or 2.5 mm?
has some benefit in the behavior of the car?
Best regards:
Pedro silva
which is the difference in using this parts camber link plate 1.25 mm or 2.5 mm?
has some benefit in the behavior of the car?
Best regards:
Pedro silva
#3561
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
[QUOTE=tallyrc;6981988]
T.O.P Racing Products 44.5mm Aluminum Universal Shaft Set (Red) (2)
[TRP-PO-SDT027RD]
http://www.amainhobbies.com/product_...haft-Set-Red-2
or just the shaft
http://www.amainhobbies.com/product_...sal-Bone-Red-1
These are the ones I was tslking about.
[TRP-PO-SDT027RD]
http://www.amainhobbies.com/product_...haft-Set-Red-2
or just the shaft
http://www.amainhobbies.com/product_...sal-Bone-Red-1
These are the ones I was tslking about.
Last edited by Nova F1 Racer; 02-10-2010 at 05:07 AM. Reason: added info
#3562
Is there a place where we can find out about the latest option parts that are coming out?
I see there is a new 'black' layshaft that looks like it has something at the end, maybe to key it in to the supports?
And there are are few other things... What's the difference between the Ally and Ti Axle pin holders? Is there much in the weight? Are there any strength issues with the Ally?
Where are the resources for this stuff?
I see there is a new 'black' layshaft that looks like it has something at the end, maybe to key it in to the supports?
And there are are few other things... What's the difference between the Ally and Ti Axle pin holders? Is there much in the weight? Are there any strength issues with the Ally?
Where are the resources for this stuff?
Last edited by BagofSkill; 02-11-2010 at 04:58 AM.
#3565
Last shipment Rubber Kit had updated Centre pulley shaft !
#3566
Tech Master
#3569
#3570
Tech Apprentice